Cisco ASR 1002 User Manual

Page 23 of 72
TOE-common-criteria(config-if)#ip address 10.10.10.110 255.255.255.0
TOE-common-criteria(config-if)#crypto map sample
TOE-common-criteria(config-if)#interface Loopback1
TOE-common-criteria(config-if)#ip address 30.0.0.1 255.0.0.0
TOE-common-criteria(config-if)#exit
TOE-common-criteria(config)# ip route 40.0.0.0 255.0.0.0 10.10.10.101
TOE-common-criteria(config)# access-list 170 permit ip 30.0.0.0 0.255.255.255
40.0.0.0 0.255.255.255
TOE-common-criteria(config)#logging source-interface Loopback1
TOE-common-criteria(config)#logging host 40.0.0.1
3.3.4.2 Syslog Server Adjacent to an IPsec Peer
If the syslog server is not directly co-located with the TOE, then the syslog server must be
located in a physically protected facility and connected to a router capable of establishing an
IPsec tunnel with the TOE. This will protect the syslog records as they traverse the public
network.
Following are sample instructions to configure the TOE to support an IPsec tunnel with aes
encryption, with 11.1.1.4 as the IPsec peer, 10.1.1.7 and 11.1.1.6 as the local IPs, and the syslog
server on the 12.1.1.0 /28 subnet.
For the following commands see the [10] Cisco IOS Configuration Fundamentals Command
References, and Cisco IOS Security Command References:
TOE-common-criteria#configure terminal
TOE-common-criteria(config)#crypto isakmp policy 1
TOE-common-criteria(config-isakmp)#encryption aes
TOE-common-criteria(config-isakmp)#authentication pre-share
TOE-common-criteria(config-isakmp)#group 14
TOE-common-criteria(config-isakmp)#lifetime 28800
TOE-common-criteria(config)#crypto isakmp key [insert 22 character preshared key]
address 10.10.10.101
TOE-common-criteria(config)#crypto isakmp key [insert 22 character preshared key]
address 40.0.0.1
TOE-common-criteria(config)#crypto ipsec transform-set sampleset esp-aes esp-sha-
hmac
TOE-common-criteria(cfg-crypto-trans)#mode tunnel
TOE-common-criteria(config)#crypto map sample 1 ipsec-isakmp
TOE-common-criteria(config-crypto-map)#set peer 11.1.1.4
TOE-common-criteria(config-crypto-map)#set transform-set sampleset
TOE-common-criteria(config-crypto-map)#match address 115
TOE-common-criteria(config-crypto-map)#exit
TOE-common-criteria(config)#interface g0/1
TOE-common-criteria(config-if)#ip address 10.1.1.7 255.255.255.0
TOE-common-criteria(config-if)#no ip route-cache
TOE-common-criteria(config-if)#crypto map sample

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g