Cisco ASR 1002 Replacing

Removing and Replacing FRUs from the Cisco
ASR 1000 Series Routers
This chapter describes procedures for removing and replacing field-replaceable units (FRUs) from Cisco ASR
1000 Series Routers:
• Removing and Replacing Cisco ASR 1000 Series Route Processors, on page 1
• Removing and Replacing Cisco ASR 1000 Series Route Processor Internal Hard Drive, on page 4
• Removing and Replacing the Hard Drive on the Cisco ASR 1002-X Router, on page 13
• Removing and Replacing the Hard Drive on the Cisco ASR 1001 Router, on page 16
• Removing and Replacing the Cisco ASR 1000 Series DIMM Memory Modules, on page 19
• Removing and Replacing Cisco ASR 1000 Router eUSB Devices, on page 40
• Removing and Replacing Cisco ASR 1000 Series Router 1 GB USB Flash Token Memory Stick, on
page 47
• Minimum Requirements of eUSB Devices Supported on Cisco ASR 1000 Series Routers, on page 49
• Removing and Replacing Cisco ASR 1000 Series Embedded Service Processors, on page 50
• Removing and Replacing Cisco ASR 1000 Series Router SPAs and SPA Interface Processors, on page
53
• Removing and Replacing the Cisco ASR 1006 Router Power Supplies, on page 57
• Removing and Replacing the Cisco ASR 1004 Router Power Supplies, on page 71
• Removing and Replacing the Cisco ASR 1002 Router Power Supplies, on page 80
• Removing and Replacing the Cisco ASR 1013 Router Power Supplies, on page 98
• Removing and Replacing the Cisco ASR 1001 Router Power Supplies, on page 107
• Repacking the Router, on page 119
Removing and Replacing Cisco ASR 1000 Series Route
Processors
Keep in mind the following points before you remove and replace a Cisco ASR 1000 Series route processor:
• The Cisco ASR 1002 Router and the Cisco ASR 1002-F Router support only the integrated Cisco
ASR1002-RP1.
• If you have two Cisco ASR 1000 Series route processors in the Cisco ASR 1006 or Cisco ASR 1013
router and you want to remove one, do not power down the router. Remove the route processor and insert
Removing and Replacing FRUs from the Cisco ASR 1000 Series Routers
1

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g