Danfoss AK-CC 550A User Manual

22 Manual RS8FS402 © Danfoss 2016-03 AK-CC 550A
Save as factory setting
With this setting you save the controller’s actual settings as a new basic setting (the
earlier factory settings are overwritten).
o67 -
Digital input signal - DI3 (high voltage input)
The controller has a digital input 3 which can be used for one of the following func-
tions:
O: The input is not used.
1) Status display of 230 V signal
2) Door function. When the input is 0 V it signals that the door is open. The refrigera-
tion and the fans are stopped. When the time setting in “A04” is passed, an alarm
will be given and refrigeration resumed. (o89)
3) Door alarm. When the input is 0 V it signals that the door is open. When the time
setting in “A04” is passed an alarm will be given.
4) Defrost. The function is started with a pulse signal. (puls on 230 V)
5) Main switch. Regulation is carried out when the input is 230 V, and regulation is
stopped when the input is 0 V.
6) Night operation. When the input is 230 V, there will be regulation for night opera-
tion.
7) Thermostat band changeover. Switch to thermostat 2 (r21)
8) Not used.
9) Not used.
10) Appliance cleaning. The function is started with a pulse signal (pulse on 230 V).
See also description on page 5.
11) Forced refrigeration at hotgas defrost when the input is 230 V.
12) Night cover
13) Not used
14) Cooling stopped with the function "Forced closing"
15) Case shut down when the input is activated.
o84 DI3 cong.
Rail heat control
The rail heat can be controlled in several ways:
0: The function is not used
1: Pulse control is used with a timer function following the day/night operation (o41
and o42)
2: Pulse control is used with a dew point function. This function requires that a signal
is received about the dew point value. The value is measured by a system manager
and sent to the controller via the data communication.
o85 Railh. mode
Dew point value where the rail heat is minimum
This function is discussed earlier in the manual.
o86 DewP Min lim
Dew point value where the rail heat is maximum
This function is discussed earlier in the manual.
o87 DewP Max lim
Lowest permitted rail heat eect
Here the % part of the eect to be achieved when the dew point value is minimum.
o88 Rail Min ON%
Start of refrigeration when door is open
If the door has been left open, refrigeration must be started after a set time. That time
can be set here.
o89 DoorInjStart
Defrosting and fan operation during forced closing
You can set whether fans should be operational or stopped if the function “Forced
closing” is activated here.
0: The fans will be stopped and defrosting will be permitted.
1: The fans will run and defrosting will be permitted.
2: The fans will be stopped and defrosting will not be permitted during a forced closing.
3: The fans will run and defrosting will not be permitted during a forced closing.
o90 Mode ForcedCl
Alternative display
A reading can be displayed by pressing the lower button on the controller. This read-
ing is set from the factory so that the defrosting stop temperature is displayed.
A dierent setting will give the following reading:
1: (Defrost stop temperature = factory setting)
2: S6 temperature
3: S5B temperature (Application 9 only)
4: S3B temperature (Application 10 only)
o92 Displ menu 2
Display of temperature during normal operation
1: Air temperature. Weighted S3 + S4
2: Product temperature S6 (not application 9 and 10)
o97 Disp. Ctrl.
Light and night blinds denition
0: Light is switched o and night blinds are open when the main switch is o
1: Light and night blinds are independent of main switch.
o98 Light MS = O

Danfoss AK-CC 550A Specifications

General

Brand	Danfoss
Model	AK-CC 550A
Category	Controller
Language	English