Danfoss EtherNet/IP Midi Drive FC 280 User Manual

3 Conguration
3.1 IP Settings
All IP-related parameters are located in parameter group
12-0* IP Settings:
•
Parameter 12-00 IP Address Assignment.
•
Parameter 12-01 IP Address.
•
Parameter 12-02 Subnet Mask.
•
Parameter 12-03 Default Gateway.
•
Parameter 12-04 DHCP Server.
•
Parameter 12-05 Lease Expires.
•
Parameter 12-06 Name Servers.
•
Parameter 12-07 Domain Name.
•
Parameter 12-08 Host Name.
•
Parameter 12-09 Physical Address.
The EtherNet/IP control cassette oers several ways of IP
address assignment.
Setting up the frequency converter with a manually
assigned IP address
Parameter Value
Parameter 12-00 IP Address Assignment [0] MANUAL
Parameter 12-01 IP Address
192.168.0.xxx
1)
Parameter 12-02 Subnet Mask
255.255.255.0
1)
Parameter 12-03 Default Gateway Optional
Table 3.1 Set-up Parameters for Manually
Assigned IP Address
1) Class C IP address example. Any valid IP address can be entered.
NOTICE
A power cycle is necessary after setting the IP
parameters manually.
Setting up the frequency converter with automatically
(BOOTP/DHCP) assigned IP address or via the hardware
switches
Parameter Value
Parameter 12-00 IP Address Assignment [1] DHCP/[2] BOOTP
Parameter 12-01 IP Address Read only
Parameter 12-02 Subnet Mask Read only
Parameter 12-03 Default Gateway Read only
Table 3.2 Set-up Parameters for Automatically
Assigned IP Address
By IP address assigned by DHCP/BOOTP server or hardware
switches, the assigned IP address and subnet mask can be
read out in parameter 12-01 IP Address and
parameter 12-02 Subnet Mask. In parameter 12-04 DHCP
Server, the IP address of the found DHCP or BOOTP server
is shown. For DHCP only: The remaining lease-time can be
read out in parameter 12-05 Lease Expires.
Parameter 12-09 Physical Address reads out the MAC
address of the option, which is also printed on the label of
the option. If using xed leases together with DHCP or
BOOTP, the physical MAC address is linked with a xed IP
address.
NOTICE
If no DHCP or BOOTP reply has been received after 4
attempts (for example, if the DHCP/BOOTP server has
been powered o), the option returns to the last good
known IP address.
Parameter 12-03 Default Gateway is optional and only used
in routed networks.
Optional parameters used with domain name server
systems:
•
Parameter 12-06 Name Servers.
•
Parameter 12-06 Name Servers.
•
Parameter 12-08 Host Name.
If DHCP or BOOTP is selected as IP address assignment,
these parameters are read-only.
3.2
Ethernet Link Parameters
Parameter group 12-1* Ethernet Link Parameters holds
Ethernet Link information:
•
Parameter 12-10 Link Status.
•
Parameter 12-11 Link Duration.
•
Parameter 12-12 Auto Negotiation.
•
Parameter 12-13 Link Speed.
•
Parameter 12-14 Link Duplex.
NOTICE
The Ethernet link parameters are unique per port.
Parameter 12-10 Link Status and parameter 12-11 Link
Duration show information on the link status per port.
Parameter 12-10 Link Status show Link or No Link according
to the status of the present port.
Parameter 12-11 Link Duration show the duration of the link
on the present port. If the link is broken, the counter
resets.
Conguration EtherNet/IP
6 Danfoss A/S © 06/2016 All rights reserved. MG07H102
33

Danfoss EtherNet/IP Midi Drive FC 280 Specifications

General

Brand	Danfoss
Model	EtherNet/IP Midi Drive FC 280
Category	DC Drives
Language	English