Home
Danfoss
DC Drives
VLT FCD 305
Danfoss VLT FCD 305 Design Guide
4
of 1
of 1 rating
144 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
VL
T
®
FCD
Series
■
Mechanical
dimensions,
motor
mounting
FCD
303
–
315
340
–
480
Volt
FCD
322
–
330
340-480
V
olt
■
Mechanical
dimensions,
stand
alone
mounting
The
drawings
below
give
the
mechanical
dimen-
sions.
All
dimensions
are
in
mm.
FCD
303-315
380-480
V
olt
FCD
322
–
330
380
–
480
V
olt
MG.04.A1.02
-
VLT
is
a
registered
Danfoss
trade
mar
k
29
Installation
28
30
Table of Contents
Default Chapter
1
Table of Contents
1
Introduction to FCD 300
3
Software Version
3
General Warning
4
These Rules Concern Your Safety
4
Warning against Unintended Start
4
Technology
5
CE Labelling
7
Order Form
8
Ordering Numbers for FCD 300, 380-480 V
10
Order Form
14
PC Software and Serial Communication
15
Accessories for FCD 300
16
The LCP 2 Control Unit, Option
23
Parameter Selection
27
Installation
29
Mechanical Measurements
29
Mechanical Dimensions, Motor Mounting
29
Mechanical Dimensions, Stand Alone Mounting
29
Mechanical Installation
30
General Information about Electrical Installation
32
EMC-Correct Electrical Installation
34
Earthing of Screened/Armoured Control Cables
36
Diagram
37
Electrical Installation
38
Mains Connection
39
Pre-Fuses
39
Motor Connection
39
Direction of Motor Rotation
39
Parallel Connection of Motors
39
Motor Cables
40
Motor Thermal Protection
40
Brake Connection
40
Earth Connection
41
Control of Mechanical Brake
41
Electrical Installation, Control Cables
42
Elektrical Installation, Control Terminals
43
VLT Software Dialog
43
Relay Connection
43
Connection Examples
44
Programming
48
Operation & Display
48
Setup Configuration
48
Load and Motor
56
DC Braking
60
References & Limits
65
Handling of References
66
Reference Function
69
Inputs and Outputs
74
Special Functions
83
PID Functions
85
Handling of Feedback
87
Serial Communication for FCD 300
94
Control Word According Tofc Protocol
100
Status Word According Tofc Profile
101
Control Word According to Fieldbus Profile
103
Status Word According to Profidrive Protocol
104
Serial Communication
106
Technical Functions
113
All about FCD 300
118
Special Conditions
118
Galvanic Isolation (PELV)
118
Earth Leakage Current and RCD Relays
118
Extreme Operating Conditions
118
Du/Dt on Motor
119
Switching on the Input
119
Acoustic Noise
119
Temperature-Dependent Switch Frequency
119
Derating for Air Pressure
120
Derating for Running at Low Speed
120
Motor Cable Lengths
120
Vibration and Shock
120
Air Humidity
120
UL Standard
120
Efficiency
120
Mains Supply Interference/Harmonics
121
Power Factor
121
Generic EMC Standards / Product Standards
122
EMC Emission
122
EMC Immunity
122
Status Messages
125
Warnings/Alarm Messages
125
Warning Words, Extended Status Words and Alarmwords
129
General Technical Data
130
Technical Data, Mains Supply 3 X 380 - 480 V
134
Available Literature
135
Supplied with the Unit
135
Factory Settings
136
Other manuals for Danfoss VLT FCD 305
Operating Instructions
127 pages
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Danfoss VLT FCD 305 and is the answer not in the manual?
Ask a question
Danfoss VLT FCD 305 Specifications
General
Brand
Danfoss
Model
VLT FCD 305
Category
DC Drives
Language
English
Related product manuals
Danfoss VLT FCD 307
127 pages
Danfoss VLT FCD 303
127 pages
Danfoss VLT FCD 315
127 pages
Danfoss VLT FCD 330
127 pages
Danfoss VLT FCD 311
127 pages
Danfoss VLT FCD 322
127 pages
Danfoss VLT FC 360
82 pages
Danfoss vlt FC 102
188 pages
Danfoss VLT FC Series
64 pages
Danfoss VLT FCM Series
106 pages
Danfoss VLT FC 302 N110
182 pages
Danfoss VLT FC 102 N250
182 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General