Denon UDRW-250 User Manual

—_
—
Tape type and remaining time display
During the editing operation, C-O0lignhts and the
tape time is displayed.
Track
number
display
Time
display
D0
is
displayed
when
the
disc
data
cannot
be
read
properly.
OOO
is
displayed
when
the
disc
data
cannot
be
read
When
a
disc
is
loaded:
properly.
e
The
total
number
of
tracks
is
displayed
in
the
stop
When
a
disc
is
loaded:
mode.
@
The
elapsed
playing
time
is
displayed
in
the
stop
mode.
e@
The
track
number
is
displayed
in
the
play
and
program
«©
The
elapsed
time
for
the
track
currently
playing
is
modes,
ed
in
the
play
and
pause
modes.
@
(Cor
JJ
is
displayed
when
the
innermost
or
outermost
e@
The
elapsed
time
for
the
programmed
tracks
is
display-
section
of
the
disc
is
reached
in
the
manual
search
ed
in
the
program
mode.
mode.
The
indicators
switch
as
follows
when
the
REPEAT
button
is
pressed
in
the
play
mode:
First press: REPEAT (single track repeat) The repeated track number lights on the
music calendar.
Second
press:
REPEAT
(all
tracks
repeat)
The
track
numbers
of
the
tracks
on
the
disc
light.
Third press: REPEAT A-
Fourth press: REPEAT A-8
Fifth press: No display
@
When
track
21
or
higher
is
repeated
in
1-track
repest,
the
TRACK
number
flashes.
D> PLAY lights when the disc is
playing, and 1 PAUSE lights when
in the pause mode.
PROGRAM lights during the programmed selection
mode.
This lights when there
ere 21 of more tracks on
the disc.
This lights when the
RANDOM button is
pressed.
AUTO OFF: Lights during the auto
off mode.
OFF: Lights when the power is
switched off.
During the editing operation, EDIT (A) TAPE lights up, the remaining time for
side A of the tape is indicated on the time section of the display, the track
numbers set for side A light on the calendar section of the display, while the
track numbers set for side B flash. When the TAPE A/B button is pressed, [A]
goes off, [5] lights, and the remaining time and track numbers set for side B
are indicated in the same way.
Music calendar display
This indicates the track numbers on the disc to a maximum of 20.
The track numbers go off after the corresponding tracks are played.
in the program mode, the track numbers of the programmed tracks are indicated to a maximum of 20.
All track numbers from 1 to 20 light when the disc data cannot be read properly.
@ NO DISC lights on the display if no disc is loaded, or if the disc is loaded upside-down or is heavily scratched or dirty.
[6] LISTENING TO RADIO BROADCASTS
(Check that connections are proper, referring to Page 5)
a | a 8888-0
eae
[ Ptarts
Example: Tuning to 87.50 MHz, FM
SYSTEM POWER
Set the VOLUME control to the
minimum position, then press the
SYSTEM POWER button.
Select the FM band with
the BAND button.
Use the UP and DOWN buttons to
set the frequency to 87.50 MHz.
Example: Presetting the (currently tuned) FM 87.80 MHz to preset number 3
090%
text THEA =6MEMORY
Press the MEMORY button.
flashes for 10 seconds.
Use the UP and DOWN buttons to
call up the number to which you
want to preset the station.
Or, directly press the number buttons!
on the remote contro! unit.
The preset number will flash.
Press the MEMORY button while
is flashing.
Up to 30 MW. LW and FM stations can be preset at random using this procedure.
Auto Tuning
@ When the TUNING buttons are pressed, the frequency changes in steps of 50 kHz for FM, 9 kHz for MW and 1 kHz for LW.
e (fthe TUNING UP or DOWN button is held in for more than 1 second, the frequency continues to change when the button is released.
The next station is tuned in automatically and the tuning stops there. Note that tuning will not stop if the antenna input is weak and the
indicator does not light. To stop the auto tuning, press the UP or DOWN button again.
G)
m
z
m
w
>
Za
”
m
i?)
a
ie)
z
SOC a a aa a a Sr ee Se

Denon UDRW-250 Specifications

General

Brand	Denon
Model	UDRW-250
Category	Stereo System
Language	English