Hitachi 32HBC01 User Manual

English - 11 -
Step 1 - Checking the TV and Accessories
Note: You should check the accessories after
purchasing. Make sure that each accessory is
included.
All models are supplied with the following items:
Instruction Book, Remote Control, 2 X AAA Batteries
and depending on which model you purchased, AV
connection Leads.
Step 2 - Installing the Batteries to the Remote
1. Lift the cover on the back of the remote gently.
2. Install two AAA/R3 batteries. Make sure the (+) and
(-) signs match (observe correct polarity).
3. Put the cover back on.
Note: Remove the batteries from remote control handset
when it is not going to be used for a long period of time.
Otherwise possible leakage from the batteries can
damage it. Operation range is approximately 7m/23ft.
Step 3 - Connect Power and Antenna/Cable
After unpacking, allow the TV set to reach the ambient room
temperature before you connect the set to the mains.
Power Cable Connection:
IMPORTANT: The TV set is designed to operate on
220-240V AC, 50 Hz.
Plug the power cable to the mains socket outlet. Leave
at least 10mm space around the TV set.
Power off both the TV and the device before
making any connections.
Antenna Connection:
Connect the aerial/cable or satellite TV plug to the
Aerial, Cable or Satellite INPUT socket located at
the rear of the TV.
Satellite and Cable connection are dependent on the
model.
insert plug...
Make sure the power
plug is plugged securely
to the wall outlet.
satellite
aerial or cable
REAR OF THE TV
Step 4 - Switching On/Off
To Switch the TV On
• Connect the power cord to the 220-240V AC, 50 Hz.
• Press Standby button. Then the standby LED lights
up.
To switch on the TV from standby mode either:
• Press the Standby button, Programme +/- or a
numeric button on the remote control.
Control buttons on the TV
• Press the Programme +/- button on the TV. The TV
will then switch on.
-or-
• Press the middle of the control switch on the left side
of the TV. The TV will then switch on.
To Switch the TV Off(Optional)
• Press the Standby button on the remote control or
press the Standby button on the TV or press and hold
the control switch on the TV until shut down, so the
TV will switch to standby mode.
• To power down the TV completely, unplug the
power cord from the mains socket.
Note: When the TV is switched to standby mode, standby
LED can blink to indicate that features such as Standby
Search, Over Air Download or Timer is active. The LED can
also blink when you switch on the TV from standby mode.

Hitachi 32HBC01 Specifications

General

Screen shape	Flat
Response time	6.5 ms
Display diagonal	32 \
Display brightness	300 cd/m²
Display resolution	1366 x 768 pixels
Native aspect ratio	16:9
LED backlighting type	Direct-LED
Contrast ratio (typical)	4000:1
Display diagonal (metric)	81 cm
Motion interpolation frequency	100 Hz
Motion interpolation technology	-
Power consumption (standby)	- W
Power consumption (typical)	41 W
3D	No
Composite video out	1
Annual energy consumption	59 kWh
Product color	Black
RMS rated power	5 W
Number of speakers	2
Audio formats supported	MP3, WAV, WMA
Image formats supported	BMP, JPG, PNG
Video formats supported	3GP, ASF, AVI, FLV, MKV, MP4, MPEG, MPG, VOB, WMV
Video compression formats	H.264, MPEG4
HDMI version	1.4
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Ethernet LAN (RJ-45) ports	0
Digital signal format system	DVB-C, DVB-T
Package depth	154 mm
Package width	915 mm
Package height	585 mm
Package weight	8600 g

Weight and Dimensions

Depth (with stand)	185 mm
Height (with stand)	478 mm
Weight (with stand)	6000 g
Depth (without stand)	97 mm
Width (without stand)	735 mm
Height (without stand)	438 mm
Weight (without stand)	6550 g