Honeywell LYNXR Installation And Setup Gude

–38–
✻
84 Assign Zone Voice Descriptors
Use this mode to assign voice descriptors for each zone. These are the descriptors that are announced when
the system announces any event involving a zone number. Each descriptor can consist of up to 3 words.
Press
✻
84 while in Programming mode.
The prompts for
✻
84 are as follows:
84 Voice Descriptors---------------------- Main Menu prompt
A 01 Zone Number --------------------------- for entering the zone number to be programmed
b Descriptor 1 ----------------------------- for assigning the first word of this zone’s descriptor
C Descriptor 2 ----------------------------- for assigning the second word of this zone’s descriptor
d Descriptor 3 ----------------------------- for assigning the third word of this zone’s descriptor
The following explains these prompts in detail. The left two columns identify the prompts and list the
available entries. The right-most column provides a further explanation of the entries.
1RWH (QWHULQJ D QXPEHU RWKHU WKDQ WKH RQH VSHFLILHG ZLOO JLYH XQSUHGLFWDEOH UHVXOWV
 
Assign zone voice descriptors
0 = exit mode
1 = enter mode
Pressing 1 advances to the next prompt below.
Pressing 0 exits mode, upon which this prompt blinks, indicating the
mode is inactive.
%
]]
Zone number
>
✻
@ FRQWLQXH WR QH[W SURPSW DQ\ H[LVWLQJ
GHVFULSWRUV ZLOO EH DQQRXQFHG WKHQ
GHVFULSWRU  ZLOO EH UHSHDWHG
 H[LW YRLFH GHVFULSWRU PRGH
Enter the 2-digit zone number for which this descriptor is being
assigned, then press [✻]. The Voice Descriptor for the selected zone will
be announced, if it is programmed.

E

YY
Descriptor 1
(QWHU >@  GLJLW YRFDEXODU\ LQGH[ QXPEHU RI
ILUVW GHVFULSWRU ZRUG IRU WKLV ]RQH
 DFFHSW ZRUG DQG DGYDQFH WR GHVFULSWRU 
GHVFULSWRU  ZLOO EH DQQRXQFHG
 DFFHSW ZRUG DQG DGYDQFH WR SURPSW $ IRU
QH[W ]RQH 3UHVV DQ\ RWKHU NH\ WR UHSHDW WKH
VHOHFWHG ZRUG
Enter the first word of the descriptor for the selected zone.
Use the [6] or [8] key to advance as described.
To change the entered index number before pressing [6] or [8], simply
press [#] + desired 2-digit vocabulary index number.
If descriptor 1 is not desired, enter [#] + 99 (blank), then press [8] to
return to zone number prompt.

'

YY
Descriptor 2
(QWHU >@  GLJLW YRFDEXODU\ LQGH[ QXPEHU RI
VHFRQG GHVFULSWRU ZRUG IRU WKLV ]RQH
 DFFHSW ZRUG DQG DGYDQFH WR GHVFULSWRU 
GHVFULSWRU  ZLOO EH DQQRXQFHG
 DFFHSW ZRUG DQG DGYDQFH WR SURPSW $ IRU
QH[W ]RQH 3UHVV DQ\ RWKHU NH\ WR UHSHDW WKH
VHOHFWHG ZRUG
Enter the second word of the descriptor for the selected zone.
Use the [6] or [8] key to advance as described.
To change the entered index number before pressing [6] or [8], simply
press [#] + desired 2-digit vocabulary index number.
If descriptor 2 is not desired, enter [#] + 99 (blank), then press [8] to
return to zone number prompt.

G

YY
Descriptor 3
(QWHU >@  GLJLW YRFDEXODU\ LQGH[ QXPEHU RI
WKLUG GHVFULSWRU ZRUG IRU WKLV ]RQH
 RU  DFFHSW ZRUG DQG DGYDQFH WR SURPSW
$ IRU QH[W ]RQH =RQH GHVFULSWRU ZLOO
EH DQQRXQFHG 3UHVV DQ\ RWKHU NH\ WR
UHSHDW WKH VHOHFWHG ZRUG
Enter the last word of the descriptor for the selected zone.
Use the [6] or [8] key to advance as described.
To change the entered index number before pressing [6] or [8], simply
press [#] + desired 2-digit vocabulary index number.
If descriptor 3 is not desired, enter [#] + 99 (blank), then press [8] to
return to zone number prompt.

Honeywell LYNXR Specifications

General

Brand	Honeywell
Model	LYNXR
Category	Security System
Language	English