39
Programming the Lock Feature
Note: If no button is pressed within 5 seconds of each selection
the screen will revert back to the Main Menu and the current set-
tings will remain active.
N.B. no symbol is shown on the display to signal that the lock
is active.
You can prevent users from changing certain features of the spa.
There are two lock modes to choice from:
• Access Lock will disable the ability to manually activate or
adjust any feature of the spa. All scheduled operations will
still be preformed.
• Settings Lock will disable the ability to change any of the
user settings. You can still activate the jet pumps and light-
ing. All scheduled operations will still be preformed.
• Service Lock (temporary lock) temporarily disables func-
tion activation, so that maintenance can be performed
(e.g. cleaning the lters).
Note: the lockout lasts 2 hours.
Do not leave the lock active for long periods, especially in the
case of low temperatures or where there is a risk of freezing.
Always disconnect the hot tub before performing any main-
tenance or repairs.
Activating a lock feature.
1. Press (
) until you get to the “LOCK” Menu. The display will
scroll “LOCK MENU.” The system returns to the main menu if no
action is taken.
2. Press or to pass from “AL” (“ACCESS LOCK”) to “SL” (“SET-
TINGS LOCK”) to “SVL” (temporary lock). Once you have made
the selection, press to save the change. The system returns to
the “LOCK MENU”.
Deactivating a lock feature.
To deactivate a lock mode, press and hold ( ) for 10 seconds.
Activation of exterior lights
1. Press ( ) until you see the “EXT” menu (Language). The words
“EXTERIOR LIGHTS” will be shown on the display screen.
Note: If no key is pressed within 5 seconds of the selection being
made, the screen will go back to the main menu and the current set-
tings will continue to apply.
2. Press ( ) to go to the dierent modes:
- HI: the lights are at maximum intensity;
- MED: the lights are at medium intensity;
- LO: the lights are at low intensity;
- OFF: the lights are o;
- AUTO: the lights are switched on every day, from 7 pm to mid-
night. To activate/deactivate this mode, use the - or + keys.
Once you have made the selection, press (
) to save the change.
The system returns to the previous menu.
Spa Maintenance
Proper and regular maintenance of your spa will help it retain its
beauty and performance.
Information regarding spa cleaning and maintenance and
the products to be used can be found in the catalogue-guide
provided with the product.
Cleaning The Filters
Your Jacuzzi spa is equipped with a skimmer bag and two high
performance pleated lter cartridges located under the lter
cover. The circulation pump drawing water through the skimmer
bag and lter cartridge lters ne debris. Large debris is ltered
by jets pump 1 drawing water through the skimmer bag and
second lter cartridge during an automated Secondary Filtration
Cycle or when jets pump 1 is manually activated during spa use.
Combined, both lters provide unsurpassed water quality by
trapping surface oils and suspended particles. The lter cartridge
should be cleaned once a month or as necessary, depending on
use, for optimum performance.
TO DECREASE RISK OF DEATH, DROWNING OR ENTRAPMENT,
ALWAYS TURN POWER TO SPA OFF BEFORE CLEANING THE
FILTER CARTRIDGES!
Refer to steps on following page for complete lter cleaning/re-
placement instructions:
B
C
D
(Filter Cover Back View)
E
F
G
Trapped
Air
Bubbles
Cartridge 1
Cartridge 2
A. TURN POWER TO SPA OFF!
B. Lift upward on lter cover to remove it from the mating retain-
ing clips. Then tilt forward to access lter cartridges.
C. Remove skimmer bag from clips, then clean out debris.
D. Rotate each lter cartridge handle counterclockwise to un-
To Next Page
Loading...
Need help?
General
