xli
目 錄
!. 規格................................................................................................................................. 7
@. 安裝................................................................................................................................. 8
1. 承托板的安裝方法 ............................................................................................................................................................................... 8
2. 皮帶護罩的安裝方法 ......................................................................................................................................................................... 11
3. 踏板的安裝方法 .................................................................................................................................................................................. 12
4. 線架的安裝 .......................................................................................................................................................................................... 13
#. 準備和運轉 .................................................................................................................. 14
1. 加油 ....................................................................................................................................................................................................... 15
2. 確認轉動方向 ......................................................................................................................................................................................17
3. 機針的安裝方法 .................................................................................................................................................................................. 18
4. 穿線方法 ............................................................................................................................................................................................... 20
5. 壓腳的調節和壓腳的拆卸................................................................................................................................................................. 23
6. 縫距長度的調節 .................................................................................................................................................................................. 24
7. 差動送布的調節 .................................................................................................................................................................................. 25
$. 維修............................................................................................................................... 29
1. 切刀和包邊寬度的調整 ..................................................................................................................................................................... 29
2. 縫紉機頭的清掃 .................................................................................................................................................................................. 32
3. 筒形濾清器的維修和更換................................................................................................................................................................. 33
4. 調整彎針和調整護針器 ..................................................................................................................................................................... 35
5. 挑線桿、底線凸輪位置尺寸（標準調整）..................................................................................................................................... 38
6. 馬達皮帶輪和皮帶 ............................................................................................................................................................................. 44
xxxviii
目 次
!. 仕様 ........................................................................................................................................ 1
@. 据え付け ................................................................................................................................ 8
1. フレーム受板の取り付け方 ................................................................................................................................................ 8
2. ベルトカバーの取り付け方 ............................................................................................................................................. 11
3. ペダルの取り付け方 ......................................................................................................................................................... 12
4. 糸立装置の取り付け方 ..................................................................................................................................................... 13
#. 準備および運転 ................................................................................................................. 14
1. 給油 .................................................................................................................................................................................... 15
2. 回転方向の確認 ................................................................................................................................................................ 17
3. 針の取り付け方 ................................................................................................................................................................ 18
4. 糸の通し方 ........................................................................................................................................................................ 20
5. 押え圧の調節と押えの外し方 ......................................................................................................................................... 23
6. 縫い目長さの調節 ............................................................................................................................................................. 24
7. 差動送りの調節 ................................................................................................................................................................ 25
$. 保守 ..................................................................................................................................... 29
1. メスとかがり幅の調整 ..................................................................................................................................................... 29
2. ミシン頭部の掃除 ............................................................................................................................................................. 32
3. カートリッジフィルタの点検と取りかえ ...................................................................................................................... 33
4. ルーパ合わせおよび針受け合わせ寸法値 ...................................................................................................................... 35
5. 天びん、下糸カム位置寸法値（標準合わせ） .............................................................................................................. 38
6. モータプーリとベルト ..................................................................................................................................................... 44
CONTENTS
!. SPECIFICATION ........................................................................................................... 2
@. INSTALLATION .............................................................................................................8
1. Installing the frame support plate ....................................................................................................................... 8
2. Attaching the belt cover..................................................................................................................................... 11
3. Installing the pedals ........................................................................................................................................... 12
4. Installing the thread stand ................................................................................................................................. 13
#. PREPARATION AND OPERATION ............................................................................14
1. Lubrication .......................................................................................................................................................... 15
2. Checking the direction of rotation .................................................................................................................... 17
3. Attaching needles............................................................................................................................................... 18
4. Threading the machine ...................................................................................................................................... 20
5. Adjusting the pressure of the presser foot and removing the presser foot ................................................. 23
6. Adjusting the stitch length ................................................................................................................................ 24
7. Differential feed mechanism.............................................................................................................................. 25
$. MAINTENANCE...........................................................................................................29
1. Knives and overedge witdh ............................................................................................................................... 29
2. Cleaning the machine head ............................................................................................................................... 32
3. Checking the cartridge filter and replacing it .................................................................................................. 33
4. Dimensions used to adjust the looper and the needle guard ........................................................................ 35
5. Dimensions relatrd to the position of the thread take-up and the looper thread cam
(standard adjustment) ........................................................................................................................................ 38
6. Motor pulleys and belts ..................................................................................................................................... 44
To Next Page
Loading...
Need help?
General
