To Next Page

To Previous Page

Installation and ConnectionInstallation and Connection

• If your car’s ignition does not have an ACC position,

connect the ignition wires to a power source that

can be turned on and off with the ignition key. If you

connect the ignition wire to a power source with a

constant voltage supply, such as with battery wires,

the battery may be drained.

• If the fuse blows, first make sure the wires are not

touching to cause a short circuit, then replace the old

fuse with one with the same rating.

• Insulate unconnected wires with vinyl tape or other

similar material. To prevent a short circuit, do not

remove the caps and do not let the cable out at the

ends of the unconnected wires or the terminals.

• Secure the wires with cable clamps and wrap vinyl

tape around the wires that comes into contact with

metal parts to protect the wires and to prevent short

circuit.

• Connect the speaker wires correctly to the terminals

to which they correspond. The unit may be damaged

or fail to work if you share the · wires or ground

them to any metal part in the car.

• When only two speakers are being connected to the

system, connect both connectors either to the front

output terminals or to the rear output terminals (do

not mix front and rear). For example, if you connect

the ª connector of the left speaker to a front output

terminal, do not connect the · connector to a rear

output terminal.

Installation procedure

1 Remove the key from the ignition and

disconnect the

· battery.

2 Make the proper input and output wire

connections for each unit.

3 Connect the speaker wires of the wiring

harness.

4 Connect the wires of the wiring harness

in the following order: ground, battery,

ignition.

5 Connect the wiring harness to the unit.

6 Install the unit in your car.

Make sure that the unit is installed securely in place.

If the unit is unstable, it may malfunction (e.g., the

sound may skip).

7 Reconnect the · battery.

8 Press the reset button on the monitor

panel. (Page3)

9 Configure <Initial Settings>. (Page5)

Parts list for installation

Note: This parts list does not include all the package

contents.

¥ Wiring harness (× 1)

ø Extension wire, 2 m (× 1)

π Flat head screws, M5 × 8 mm (× 6)

[ Round head screws, M5 x 8 mm (× 6)

“ Microphone, 3 m (× 1)

Only for KW-V350BT Region 4

] Trim plate (× 1)

‘ Steering remote cable (× 1)

ENGLISH

00_KWV_2019ST_KR.indb 5300_KWV_2019ST_KR.indb 53 1/6/2018 8:19:23 AM1/6/2018 8:19:23 AM

Questions and Answers:

Need help?

Do you have a question about the JVC KW-V250BT and is the answer not in the manual?

JVC KW-V250BT Specifications

General

Dimmer	Yes
DIN size	2 DIN
Output power	- W
Product color	Black
Disc types supported	CD, CD-R, CD-RW, DVD, DVD+R, DVD+RW, DVD-R, DVD-RW
Audio output channels	- channels
Equalizer bands quantity	13
Maximum power per channel	50 W
Analog signal format system	NTSC, PAL
Display type	LCD
Display diagonal	6.2 \
Display resolution	800 x 480 pixels
Illumination color	White
Audio formats supported	AAC, FLAC, MP3, WAV, WMA
Image formats supported	JPEG
Video formats supported	DIVX, MPEG1, MPEG2
USB version	2.0
Bluetooth version	3.0+HS
USB port position	Front
Bluetooth profiles	A2DP, AVRCP
USB connector type	USB Type-A
USB ports quantity	1
Hands-free calling	Keep your hands on wheel with Bluetooth™ Hands-free calling. After pairing your compatible Bluetooth mobile phone to your TomTom GPS, you’ll be able to see incoming call information, make and answer calls, and talk hands-free through your device. You’ll e
AM band range	531 - 1611 kHz
FM band range	87.5 - 108 MHz
LW band range	153 - 279 kHz
Preset stations quantity	20
Package weight	2900 g