10
English
Turning On the Power
To turn on the unit, press
STANDBY/ON .
The STANDBY/ON lamp lights
green and “HELLO” appears on
the display.
• When you press the source button—CD 3/8, TAPE 2 3,
FM/AM, and AUX, the unit automatically turns on and
starts playback if the source is ready.
To turn off the unit (standby), press STANDBY/ON
again.
The STANDBY/ON lamp lights red and “GOOD BYE”
appears on the display.
•“0:00” flashes on the display until you set the built-in
clock. After setting the clock, the clock time will appear on
the display while the unit is on standby.
The illumination and display brighten only for 4 seconds
by pressing DIMMER.
• A little power is always consumed even while the unit is on
standby.
To switch off the power supply completely, unplug the AC
power cord from the AC outlet.
When you unplug the AC power cord or if a power
failure occurs
The clock is reset to “0:00” right away, while the tuner preset
stations (see page 12) will be erased in a few days.
Adjusting the Volume
You can adjust the volume level only while the unit is turned
on. The volume level can be adjusted between “VOL MIN”
and “VOLUME 1” – “VOLUME 40 (VOL MAX).”
On the remote control:
Press VOLUME + to increase the volume or
press VOLUME – to decrease it.
On the unit:
Turn VOLUME + / – control clockwise
(+) to increase the volume or
counterclockwise (–) to decrease it.
For private listening
Connect headphones to the PHONES jack.
No sound comes out of the speakers. Be sure to turn down the
volume before connecting or putting on headphones.
DO NOT turn the unit off (standby) with the volume
set to an extremely high level; otherwise, the
sudden blast of sound can damage your hearing,
speakers and/or headphones when you turn on the
unit or start playing any source next time.
REMEMBER you cannot adjust the volume level
while the unit is on standby.
VOLUME
UP
DOWN
Continued
Enjoying Sound Effects
You can adjust the sound by using various sound effect
functions.
• These functions only affect the playback sound, and do not
affect your recording.
To adjust the tone (Bass/Treble)
You can adjust the bass level (low frequency range) and the
treble level (high frequency range) within a range of –5 to +5.
When shipped, the bass level set to “BASS +2” and the treble
level set to “TREBLE +2.”
• There is a time limit in doing the following steps. If the
setting is canceled before you finish, start over from step
1
.
• For UX-J50 only, you can also use BASS and TREBLE on
the unit for this operation.
1
Press BASS to adjust the
bass level or press TREBLE
to adjust the treble level.
• Each timer you press the button,
“BASS” and “TREBLE” appears in the display
alternately.
2
Press UP to increase the level
or press DOWN to decrease it.
To reinforce the bass sound
You can reinforce the bass sound to maintain rich, full bass at
low volume—Active Hyper Bass Pro.
For UX-J60:
Press AHB PRO.
• Each time you press the button, the Active
Hyper Bass Pro is turned on (AHB ON) and
off (AHB OFF) alternately. When it is turned
on, the AHB indicator lights up on the display.
For UX-J50:
Press AHB PRO until “AHB 1” or “AHB 2”
appears on the display.
The AHB indicator also lights up on the display.
• Each time you press the button, the bass
reinforcement changes as follows:
•“AHB 2” has much more bass reinforcement effect than
“AHB 1.”
To cancel the effect, press AHB PRO until “AHB OFF”
appears on the display and the AHB indicator goes off.
AHB
PRO
AHB OFF
(Canceled)
AHB 1
AHB 2
AHB
PRO
AHB
BASS
TREBLE
STANDBY/ON
EN01-13_UX-J60&50[UW]f.pm6 03.3.13, 7:07 PM10
To Next Page
Loading...
Need help?
General
