Kenmore 625.348670 User Manual

HOW YOUR WATER SOFTENER WORKS
SECTION 2
10
2A. FACEPLATE TIMER FEATURES
EXTRA RECHARGE
Sometimes, a manually started regeneration (re-
charge) may be desired, or needed. Two examples
are:
--You have used more water than usual (guests
visiting)andyoumayrunoutofsoftwaterbeforethe
next timer started regeneration.
--Youdidnotrefillthesoftenerwithsaltbeforeitwas
gone.
You can start a regeneration right away, or you can
set the timer to regenerate at the next 2:00 AM (or
other preset recharge time). Do the following.
RECHARGE NOW
n Press the ON/OFF-HOLD
button and hold until RE-
CHARGE, SERV and FILL be-
gin to flash in the display.
Upon reaching fill, the first
cycleofregeneration,theflash-
ing SERV goes off and FILL is on steady. RE-
CHARGE continues to flash. This regeneration
willlastforabout2-1/2to2-3/4hours.Afterthis
time, you will have soft water again.
*NOTE:
If the CLEAN feature is set to ON, a cleaning
backwash precedesthe recharge.CLEAN andBkwsh
orRinseflashesinthedisplay,alongwiththeminutes
of the clean cycle remaining.
RECHARGE TONIGHT
n Pressandrelease(donothold)
the ON/OFF-HOLD button.
RECHARGE TONIGHT
flashes in the display, and the
softenerbegins regenerationat
the next preset recharge time.
Press and release the ON/OFF-HOLD button
once more if you decide to cancel the regenera-
tion, and RECHARGE TONIGHT.
SALT MONITOR SYSTEM
The faceplate timer has a low salt monitor with an
indicatorlighttoremindyoutorefillthestoragetank
with salt. To set this monitor system:
1. Lift the salt hole cover and level the salt in the
storagetank(presstanklightbuttontolightinside
of tank).
2. The salt level decal, on the brinewell inside the
tank, has numbers from 0 to 8 (see drawing on
page 9 and below). Observe the number the
leveled salt is at or closest to.
3. Now, press the SALT LEVEL ADJUST button
until black bars display up to the salt level
number. For example, the pictures below show
the salt level at 6.
4. Finally, set the level you want the low salt
indicator light to come on. Press the SIGNAL
LIGHT ADJUST button until a (T) shows oppo-
site this number. In the example below, the light
willcomeonwhenthestoredsaltdropstolevel2.
At level 2, the storage tankis about1/3full.This
is the lowest you should allow the stored salt
level to drop to. To turn the salt monitor off,
press the button until OFF shows.
SALT
LEVEL
brinewell
decal
salt
level
bars, salt
level
8
7
6
8
7
6
5
4
3
2
1
SALT
LEVEL
SIGNAL
LEVEL
TANK
LIGHT
SIGNAL
LIGHT
ADJ.
SALT
LEVEL
ADJ.
indicator light
LOW SALT
NOTE:
For accurate salt monitor operation, always use
nugget or pellet water softener salt. See page 9. If
potassium chloride is used, be sure to adjust the
timer to the KCl setting on page 7.
8
7
6
5
4
3
2
1
SALT
LEVEL
SIGNAL
LEVEL
PM
RECHARGE
Serv
Fill
8
7
6
5
4
3
2
1
SALT
LEVEL
SIGNAL
LEVEL
PM
RECHARGE TONIG
H

Kenmore 625.348670 Specifications

General

Brand	Kenmore
Model	625.348670
Category	Water Dispenser
Language	English