Introduction
Table of Contents
AP-SC7072 Skid Cutter 326-974MK 2/6/19
6
Owner Assistance
The dealer should complete the Online Warranty
Registration at the time of purchase. This information is
necessary to provide you with quality customer service.
The parts on your Skid Cutter have been specially
designed by Kubota/Land Pride and should only be
replaced with genuine Kubota parts. Contact a Kubota
dealer if customer service or repair parts are required.
Your Kubota dealer has trained personnel, repair parts,
and equipment needed to service the attachment.
See “Specifications & Capacities” on page 25 and
“Features & Benefits” on page 27 for additional
information and performance enhancing options.
Serial Number
For quick reference and prompt service, record model
and serial number on the inside cover page and again on
the warranty page. Always provide model number and
serial number when ordering parts and in all
correspondences with your Kubota dealer. For location of
your serial number plate, see Figure 1.
Serial Number Plate Location
Figure 1
Further Assistance
Your Kubota dealer wants you to be satisfied with your
new attachment. If for any reason you do not understand
any part of this manual or are not satisfied with the
service received, the following actions are suggested:
1. Discuss any problems you have with your attachment
with your dealership service personnel so they can
address the problem.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
problem, and request assistance.
3. For further assistance write to:
Kubota by Land Pride
Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address
lpservicedept@landpride.com
NOTE: A special point of information that the
operator should be aware of before continuing.
70402
Manual Storage Tube
Introduction
Kubota welcomes you to the growing family of new
product owners. This Skid Cutter has been designed with
care and built by skilled workers using quality materials.
Proper assembly, maintenance, and safe operating
practices will help you get years of satisfactory use from
this product.
Application
SC7072 construction-grade Skid Cutter is designed with
the commercial or high use consumer in mind. It features
a rigid hitch mounting system, 1/4" thick deck, 4 swinging
blades, and a bi-fold door on the front. The SC7072 is
capable of cutting and shredding brush or trees up to 7" in
diameter. Carbide mulching teeth mounted on the bottom
of the blade carrier can be used for grinding stumps.The
strong push bars on top and under the door of the
SC7072 Skid Cutter allow the operator to push trees and
brush over and away from the operator as they are being
cut without damaging the unit. The ability to cut and
mulch trees and stumps level to the ground makes this
cutter ideal for clearing right-of-ways along road sides,
pipelines or under electrical transmission lines with the
speed and efficiency needed by today’s contractors.
Farmers, ranchers and land developers will also benefit
from this unit when clearing pastures or new
development areas. The SC7072 Skid Cutter utilizes the
power, compact size, and the go anywhere ability of a
SVL to access over grown areas where a tractor and
rotary cutter cannot go. The wide, full-length tapered skid
shoes prevent the cutter from digging in or getting hung
up in the soft ground usually found under heavy brush.
Use if this skid cutter is limited to standard brush cutting.
Use in significantly larger or denser brush will result in
excessive heat and may damage the skid cutter or the
skid steer.
Using This Manual
•
This Operator’s Manual is designed to help familiarize
you with safety, assembly, operation, adjustments,
troubleshooting, and maintenance. Read this manual
and follow the recommendations to help ensure safe
and efficient operation.
• The information contained within this manual was
current at the time of printing. Some parts may change
slightly to assure you of the best performance.
• To order a new Operator’s or Parts Manual, contact
your authorized dealer.
• Store your Operator’s Manual in the dry storage tube.
See Figure 1 on page 6 for location of storage tube.
Terminology
“Right” or “left” as used in this manual is determined by
facing the direction the machine will operate while in use
unless otherwise stated.
Definitions
IMPORTANT: A special point of information related
to the following topic. Kubota’s intention is this
information must be read & noted before continuing.
To Next Page
Loading...
Need help?
General
