Makita DTM50Z User Manual

4 ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model DTM40 DTM50
Oscillation per minute 6,000 - 20,000 (min
-1
)
Oscillation angle, left/right 1.6 ° (3.2 ° total)
Overall length 307 - 324 mm
Net weight 1.7 - 2.0 kg 1.8 - 2.2 kg
Rated voltage D.C. 14.4 V D.C. 18 V
• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange
without notice.
• Specicationsmaydifferfromcountrytocountry.
• Theweightmaydifferdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-
estcombination,accordingtoEPTA-Procedure01/2014,areshowninthetable.
Applicable battery cartridge and charger
Batterycartridge D.C.14.4 V Model BL1415N / BL1430 / BL1430B / BL1440 / BL1450 / BL1460B
D.C.18 V Model BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
Charger DC18RC/DC18RD/DC18RE/DC18SD/DC18SE/DC18SF
• Someofthebatterycartridgesandchargerslistedabovemaynotbeavailabledependingonyourregionof
residence.
WARNING: Only use the battery cartridges and chargers listed above.Useofanyotherbatterycartridges
andchargersmaycauseinjuryand/orre.
Intended use
The tool is intended for sawing and cutting wood,
plastic,gypsum,non-ferrousmetals,andfastening
elements (e. g. unhardened nails and staples). It is also
intendedforworkingsoftwalltiles,aswellasdrysand-
ingandscrapingofsmallsurfaces.Itisespeciallyfor
workingclosetoedgeandushcutting.
Noise
ThetypicalA-weightednoiseleveldeterminedaccord-
ingtoEN62841:
Workmode:Sanding
Soundpressurelevel(L
pA
):78dB(A)
Uncertainty(K):3dB(A)
Thenoiselevelunderworkingmayexceed80dB(A).
Workmode:Cuttingwithplungecutsawblade
Model DTM40
Soundpressurelevel(L
pA
):82dB(A)
Soundpowerlevel(L
WA
):93dB(A)
Uncertainty(K):3dB(A)
Model DTM50
Soundpressurelevel(L
pA
):84dB(A)
Soundpowerlevel(L
WA
):95dB(A)
Uncertainty(K):3dB(A)
Workmode:Cuttingwithsegmentalsawblade
Soundpressurelevel(L
pA
):81dB(A)
Soundpowerlevel(L
WA
):92dB(A)
Uncertainty(K):3dB(A)
Workmode:Scraping
Model DTM40
Soundpressurelevel(L
pA
):81dB(A)
Soundpowerlevel(L
WA
):92dB(A)
Uncertainty(K):3dB(A)
Model DTM50
Soundpressurelevel(L
pA
):83dB(A)
Soundpowerlevel(L
WA
):94dB(A)
Uncertainty(K):3dB(A)
Wear ear protection
Vibration
Thevibrationtotalvalue(tri-axialvectorsum)deter-
minedaccordingtoEN62841:
Workmode:Sanding
Vibrationemission(a
h
):2.5m/s
2
or less
Uncertainty(K):1.5m/s
2
Workmode:Cuttingwithplungecutsawblade
Model DTM40
Vibrationemission(a
h
):9.5m/s
2
Uncertainty(K):1.5m/s
2
Model DTM50
Vibrationemission(a
h
):10.0m/s
2
Uncertainty(K):1.5m/s
2
Workmode:Cuttingwithsegmentalsawblade
Model DTM40
Vibrationemission(a
h
):5.0m/s
2
Uncertainty(K):1.5m/s
2

Makita DTM50Z Specifications

General

Uncertainty K	1.5 m/s²
Ergonomic design	Yes
Product color	Black, Blue
Multi-tool applications	-
Power protection features	Overload
Power source	Battery
AC input voltage	18 V
Oscillation angle	1.6 °
Sound pressure level	78 dB
Idle oscillation rate (max)	20000 OPM
Idle oscillation rate (min)	6000 OPM
Vibration level (segment saw blade)	2.5 m/s²
Vibration level (plunge cut saw blade)	5.5 m/s²

Weight and Dimensions

Depth	80 mm
Width	324 mm
Height	122 mm
Weight	2200 g