To Next PageTo Next PageTo Previous PageTo Previous Page
Need help?Do you have a question about the Mercury 8 and is the answer not in the manual?
General| Full Throttle RPM | 5000-6000 RPM |
|---|---|
| Cylinders | 2 |
| Gear Ratio | 2.08:1 |
| Horsepower | 8 HP |
| Starting | Manual |
| Shaft Length | 15 in, 20 in |
| Fuel Tank Capacity | External |
Process for transferring the limited warranty to a subsequent owner.
Instructions for registering the product with Mercury Marine in the US and Canada.
Procedures for registering the product outside the US and Canada.
Details the limited warranty for outboards in specific geographical regions.
Specifies the limited warranty terms for outboards in the Middle East and Africa.
Outlines the three-year warranty coverage against corrosion damage.
Clarifies what is covered by warranty and common exclusions.
Defines the operator's duties for safe boat operation and occupant safety.
Guidance on reading the manual and understanding safe operation.
Information on maximum horsepower limits and capacity plates.
Recommendations for operating high-speed or high-performance boats.
Details about remote control setup for starting.
Important safety notice regarding steering link rod fasteners.
Explains the purpose and function of the lanyard stop switch.
Safety guidelines for preventing injury to people in the water.
Safety advice for passengers on pontoon and deck boats.
Hazards and precautions related to operating over waves and wakes.
Guidance on operating in shallow water and avoiding underwater obstacles.
Alerts about carbon monoxide poisoning from engine exhaust.
Advice on choosing and installing genuine Mercury accessories.
General recommendations for safe boating practices.
Instructions on recording the outboard's serial number for reference.
Technical specifications for 8/9.9 4-Stroke models sold internationally.
Diagrams identifying components on standard outboard models.
Diagrams identifying components on Bigfoot outboard models.
Procedures for safely carrying and transporting the outboard.
Safety warnings and instructions for transporting portable fuel tanks.
Guidance on trailering boats with power tilt outboards.
Guidance on trailering boats with non-power tilt outboards.
Guidelines on recommended gasoline types, octane ratings, and fuel quality.
Specifications for recommended engine oil viscosity and classifications.
Instructions on how to check the engine oil level correctly.
Description of controls and features on the tiller handle.
Explanation of controls and features on remote control units.
Details on the engine's warning system and oil pressure light.
Explanation of the power tilt function for adjusting outboard position.
Procedure for tilting the outboard up and down.
How to adjust the vertical transom angle for optimal performance.
Steps to adjust the outboard's transom angle for better ride and handling.
Using shallow water drive positions to prevent bottom contact.
Detailed steps for tilting the outboard to its full up position.
How to adjust the trim tab to compensate for steering torque.
Essential checks to perform before starting the engine.
Guidelines for operating the outboard in freezing conditions.
Recommendations for flushing the engine after use in salt or polluted water.
Instructions for using the outboard as an auxiliary power source.
Step-by-step instructions to follow before starting the engine.
Crucial steps for breaking in the engine to ensure longevity.
Procedure for starting the engine on tiller handle models.
Steps to adjust the outboard's transom angle for better ride and handling.
Using shallow water drive positions to prevent bottom contact.
Detailed steps for tilting the outboard to its full up position.
Specific procedures for starting a warm or hot engine.
How to properly shift gears for forward, neutral, and reverse.
Instructions for safely stopping the outboard engine.
Procedure for starting the engine using the emergency starter rope.
General advice for keeping the outboard in optimal operating condition.
Defines the owner's role in performing routine engine maintenance.
Lists periodic inspections and maintenance tasks required.
Procedure for flushing the outboard's cooling system with fresh water.
Steps for removing and reinstalling the engine's top cowl.
Guidelines for inspecting the battery to ensure starting capability.
Tips for cleaning and waxing the outboard's exterior finish.
Safety precautions and inspection procedures for the fuel system.
Instructions for inspecting and replacing the fuel line filter.
Important information on fastening steering link rods securely.
Explanation of the corrosion control anode and its inspection.
Safety and procedural steps for replacing the outboard propeller.
Guidance on inspecting and replacing spark plugs.
How to inspect the timing belt for wear or damage.
Detailed procedure for changing the engine oil.
Instructions for draining, filling, and checking gearcase lubricant.
Procedure for checking and refilling the power tilt fluid.
Immediate service requirements for an outboard submerged in water.
Key considerations for preparing the outboard for storage.
Steps to protect external components during storage.
Measures to protect internal engine parts during storage.
Recommended positions for storing the outboard to prevent damage.
Instructions for proper storage and maintenance of the battery.
Possible causes and solutions when the starter motor doesn't crank.
Common reasons and troubleshooting steps for an engine that won't start.
Troubleshooting steps for an engine that is running erratically.
Diagnosing and resolving issues causing a loss of engine performance.
Possible causes and solutions for a battery that won't hold a charge.
Information on returning the outboard to an authorized dealer for service.
How to find service when away from your local authorized dealer.
Where to direct inquiries for genuine replacement parts and accessories.
Steps to take if you need additional assistance with your product.
Contact information for Mercury Marine service offices worldwide.
Information on maximum horsepower limits and capacity plates.
Safety feature preventing engine start in gear.
Advice on choosing and installing genuine Mercury accessories.
Step-by-step guide for correctly mounting the outboard on the transom.
Instructions for installing the remote control system.
Lubrication and installation of the steering cable.
Important information on fastening steering link rods securely.
Procedure for connecting the remote wiring harness.
General instructions for installing control cables.
Specific steps for installing the throttle control cable.
Specific steps for installing the shift control cable.
Guidance on mounting and installing the battery for electric start models.
Correct procedures for connecting and disconnecting battery cables.
Safety and procedural steps for installing the outboard propeller.
