Meyer Sound DS-2P User Manual

2
According to ISO/IEC Guide and EN 45014
The product herewith complies with the require-
ments of the Low Voltage Directive 73/23/EEC and
the EMC Directive 89/336/EEC.
declares that the product:The Manufacturer:
Product Name: DS-2P
Product Options: All
Name: Meyer Sound Laboratories
Address: 2832 San Pablo Avenue
Berkeley, California 94702-2204, USA
conforms to the following Product Specifications:
Safety: EN 60065: 1994
EMC: EN 55022: 1987 - Class A
IEC 801-2: 1984 - 8 kV
IEC 801-3: 1984 - 3 V/m
IEC 801-4: 1984 - 0.5 kV Signal Lines,
Meyer Sound Laboratories, Inc.
2832 San Pablo Avenue
Berkeley, California 94702
Telephone:510 - 486 - 1166
FAX: 510 - 486 - 8356
E-mail: techsupport@meyersound.com
http://www.meyersound.com
Made by Meyer Sound, Berkeley, CA, USA
European Office:
Meyer Sound Germany
GmbH
Carl Zeiss Strasse 13
56751 Polch, Germany
UU
LL
CC
UU
LL
®®
LISTED
3K59
COMMERCIAL
AUDIO SYSTEM
Meyer Sound Germany
Gmbh
Carl Zeiss Strasse 13
56751 Polch, Germany
Telephone: 49.2654.9600.58
FAX: 49.2654.9600.59
Declaration of Conformity
Contact Information
Office of Quality Manager
Berkeley, California USA
October 1, 1995
1.0 kV Power Lines
Shock: 30 g 11 msec half-sine
on each of 6 sides
Vibration: 10 – 55 Hz (0.010 m
peak-to-peak excursion)
Operating temperature:0° C to +45° C
Nonoperating temp: < –40° C or > +75° C
Humidity: to 95% at 35°C
Operating altitude: to 4600 m (15,000 ft)
Nonoperating altitude: to 6300 m (25,000 ft)
Environmental Specifications for
Meyer Sound Electronics Products
!
Pour indiquer les risques
résultant de tensions
dangereuses
Zu die gefahren von
gefährliche spanning zeigen
Important operating
instructions
Pour indequer important
instructions
Frame or chassis
Masse, châssis
Rahmen oder chassis
Protective earth ground
Terre de protection
Die schutzerde
Para indicar azares provengo
de peligroso voltajes
Para indicar importante
funcionar y mantenimiento
instrucciones
Armadura o chassis Tierra proteccionista
These symbols indicate important safety or operating features in this booklet and on the chassis.
Dangerous voltages:
risk of electric shock
Symbols Used
Zu wichtige betriebs-
anweisung und unter-
haltsanweisung zeigen

Meyer Sound DS-2P Specifications

Acoustical

frequency response	± 4 dB 50 – 160 Hz
phase response	± 60° 60 – 200 Hz
maximum SPL (music as source)	140 peak
maximum SPL (pink noise as source)	136 dB continuous; 140 peak
dynamic range	> 120 dB
coverage	120° H x 120° V

Transducers

low frequency transducer	Two 15" diameter MS-15 cone

Audio Input

input type impedance	10 kΩ
connector	XLR (A-3) male and female
nominal input level	+4 dBu (1.23 Vrms)

Amplifiers

amplifier type	Complementary power MOSFET output stages class AB/H
burst capability	1240 Watts (620 Watts per channel)
THD, IM, TIM	< .02 %

AC Power

connector	250 V NEMA L6-20P / IEC 309 Twistlock male receptacle
automatic voltage selection	85 – 134 V / 165 – 264 V; 50 Hz / 60 Hz
max continuous RMS current (115 V)	8 A
max continuous RMS current (230 V)	4 A
max continuous RMS current (100 V)	10 A
max burst RMS current (115 V)	15 A
max burst RMS current (230 V)	8 A
max burst RMS current (100 V)	18 A
max peak current during burst (115 V)	22 Apk
max peak current during burst (230 V)	11 Apk
max peak current during burst (100 V)	25 Apk
soft-current turn-on inrush current	< 12A @115V

Physical

dimensions	21.25” W x 56.75” H x 30” D
weight	221 lb (100 kg)
shipping weight	267 lb (121 kg)