Multiplex EUROPA mc 1010 User Manual

SEFyOS
(travels,
centre,
direction)
How do
you
adjust
servos?
Your ELIROPA
mc transmitter
includes the
menu
point
SERVO
lol
adjusting
servo travel,
cenlre, and
direction of
rotation.
To keep the
explanations
as simple
as
possible,
the three
processes
are described
below
separately.
The flow diagram on the
right shows
how
you
move
to the different
adjustment
sections.
Important
points
to
note:
.
OS
(OUICK-SELECT) is the
most direct
route.
A brief stick
movement
takes
you
directly
to
level
3 and
selects
the
servo
you
wish to adjust
.
You can't use QS
to reverse servos.
This is intentional, and
avoids the danger
of
reversing servos
accidentally.
.
When everything
is set up correctly,
return to the Status
display.
To do this
just
press
the
E
button
to
return to the
menu
point
SERVO,
then
R to
get
back to the
Status display.
.
The
R
button
means
Fleverse or
Reset,
At
level 2 the R button
reverses the selected
servo.
At level 3 the
R
button
resets
travels
to
100% and centre to
0%.
Servo
centre
and travel
adiustment
1.
Select
the
menu
point
SERVO
(but
don't
activate
it)
Starting
from
the
Status display
press
the
+ button twice,
then
select the
menu
ooint
SEBYO.
lf another
menu
point
has already been
selected,
move the
marker
under the
menu
point
SEBVO
using the
+/- buttons.
The menu
point
is
now
selected,
but
not
yet
activated.
2. Select the
servo using QUICK-SELECT
(OS)
Move the
transmitler
control
(stick,
pot
or switch)
brief
ly
corresponding
to the servo
you
wish to adjust. QS
takes
you
directly
to centre
and servo
travel adjustment.
QUICK-SELECT
give
you
audible
confirmation,
and
a dark
background
appears
behind
the code
number of
the servo
selected.
In the bottom
left-hand corner of
the display
a symbol appears
which
varies according to
the
position
of the transmitter
control:
.
a dot,
if the centre
is selected,
or
.
one of two
arrows,
it a direction
ol travel
is selected.
After using QUICK-SELECT
you
would usually
release the
transmitter
control,
which in
most cases
means that the
dot
appears
in the display.
3.
Altering the centre
Move the
control to
centre
-
not torgeüing
the lrim
lever. The dot
should
now appear
in the display
at bottom
ieft.
You can
now adjust
the centre
position
using the
+/- buttons.
The servo
centre can
be shifted to
either side
by about
half the
servo's
normal travel,
and
you
can
walch the ellect
of any
change
on
your
model.
.
Tapping the button
briefly
moves the
servo one step.
.
Pressing
and
holding the button
moves the
servo
in
a
continuous
series of
steps until
you
release the button.
At each
step
you
will hear a
quiet
beep.
.
lf
you
do
not
alter
the centre
position,
or
if
you
press
the
R
button, the
0% field
will have a dark
background.
Level 1
Level2
Level3
EI
EI
a
.',
.
-
cente
lett/fowad
ight/back
o
cenlrc
vh
@t
Manual
EUROPA
mc
Reverse
B
+
Adjust sevo
and cenl
centre
for
servo
2 to 0"/o
+€ft
I
E/8...
o) o)
o)
GB-10-
@;

Multiplex EUROPA mc 1010 Specifications

General

Brand	Multiplex
Model	EUROPA mc 1010
Category	Remote Control
Language	English