Multiplex EUROPA mc 1010 User Manual

The
function
"now
more,
now less"
The
Dual Rates
function
(DR
for
short)
makes it
possible
to
set up a
servo
with
two
different travels,
and switch
between
them at
will Large
control
surface
travels are
required
whenever the
model is
required to
respond
qurckly
and
powerfully.
Reduced travels
give you
more sensi-
tive
control,
which can
help to
produce
smoother
manoeuvres
The
EUROPA
mc is
preDared
for Dual Rates on
channels
1
and
2. DR
is switched
on and off separately
for
each
channel.
The DR switches
are
optional,
and
have to be
fitted
by
the user.
lnstalling
and connecting
Dual
Rates switches
Please use
either of the
MULTIPLEX
two-position
switches
listed
below:
Order
No. 7 5742
(short
toggle)
Order
No.
7
5743
(long
toggle).
'|,
open
the transmitter
case
(see
illustration).
Remove the charge
socket cap betore
you
remove the two
lalches.
2. Cut away
the
film
over
the switch
position
you
wish to use'
You can use any
of the eight
switch
wells on either side
of the
display.
3.
Install the
switch or switches
and
tighten the
securing
nut.
4.
connect
the
switches
The sticker
inside the transmitler
shows
where the
DR
switches
are
plugged
in.
.
Channel
1
-
connector
8
.
Channel
2
-
connector
9
Check
that the
plug
engages
on all three
contacl
pins
on the
transmitter
circuit board.
lf
the
switch operates
in
the
wrong direction
(it
is
a
matter of
preference)
simply
turn the
plug
through
1
80
degrees.
5. Close
the
transmitter
case.
Setting
Dual Rates
travels
The
"normal"
control surface
travel
is set up
in the
menu
point
SEflyO'
where
you
can
adjust both
sides separately.
Make these adjustments
first, so that
your
servos
work correctly
under
normal circumstances.
When
you
adjust
servo travel
under the
menu
point
DR
MN, the altered
travel applies
to
both sides
of neutral equally.
Example:
Normal travel:
left 40 degrees,
right 30 degrees
DR travel
reduction set to
half:
DR
travel
left 20 degrees,
right 15 degrees
To set
DR travel
we will start
from the Status
display again.
1. Select the
menu
point
DR
MN, but do
not activate
it
Press the
+ button three
times.
The menu
point
is now selected'
but
nol
yet
activated.
2. Select
the
DR
channel
using
QUICK-SELECT
Move the
stick corresponding
to
the channel
you
wish to adjust
(channels
1
or
2 only). QUICK-SELECT
leads
you
directly
to
servo
travel adjustment.
You cannot
move to this
adjustment
tacility using
the +/-
buttons.
3.
Move DR switch
to the ON
Position
DR
is
only
active
when both arrows
appear
in the display,
and
you
can
then set
the
reduced travel using
the
+/-
buttons.
Remove
latches
ill
transminer
Cut outtiln
Fig.9:
Prcpareopening
for switches
Fig.10:
Connecting
DR switches
t10
TGnsmitterelect@nics
EEIE
l(t"1".1,,
-
DR channel2
llz
s
a
s a
z
or
rl@t
a
s a
z
7
,/
DR is ON
Manual EUBOPA
mc
G8.12

Multiplex EUROPA mc 1010 Specifications

General

Brand	Multiplex
Model	EUROPA mc 1010
Category	Remote Control
Language	English