English – 2
GENERAL WARNINGS: SAFETY - INSTALLATION - USE (original instructions in Italian)
CAUTION Important safety instructions. Follow all instructions as improper installation may cause serious damage
CAUTION Important safety instructions. It is important for you to comply with these instructions for your own and other
people's safety. Keep these instructions
• Before commencing the installation, check the “Product technical specications”, in particular whether this product is suitable for automating
your guided part. If it is not suitable, DO NOT continue with the installation.
• The product cannot be used before it has been commissioned as specied in the chapter on “Testing and commissioning”
CAUTION According to the most recent European legislation, the implementation of an automation system must comply
with the harmonised standards provided by the Machinery Directive in force, which enables declaration of the
presumed conformity of the automation. Taking this into account, all operations regarding connection to the
electricity grid, as well as product testing, commissioning and maintenance, must be performed exclusively by
a qualied and skilled technician!
• Before proceeding with the installation of the product, check that all materials are in good working order and suited to the intended
applications
• The product is not intended for use by persons (including children) with reduced physical, sensory or mental capacities, nor by anyone with
insufcient experience or familiarity.
• Children must not play with the appliance
• Do not allow children to play with the xed control devices of the product. Keep the remote controls out of reach of children.
CAUTION In order to avoid any danger from inadvertent resetting of the thermal cut-off device, this appliance must not be powered
through an external switching device, such as a timer, or connected to a supply that is regularly powered or switched off by
the circuit
• Provide a disconnection device (not supplied) in the plant’s mains power supply, with a contact opening distance that permits complete
disconnection under the conditions dictated by overvoltage category III
• Handle the product with care during installation, taking care to avoid crushing, denting or dropping it, or allowing contact with liquids of any
kind. Keep the product away from sources of heat and naked ames. Failure to observe the above can damage the product, and increase
the risk of danger or malfunction. If this should happen, stop installation immediately and contact Customer Service.
• The manufacturer assumes no liability for damage to property, items or persons resulting from non-compliance with the assembly instructions.
In such cases the warranty for material defects is excluded
• The weighted sound pressure level of the emission A is lower than 70 dB(A)
• Cleaning and maintenance to be carried out by the user must not be carried out by unsupervised children
• Before working on the system (maintenance, cleaning), always disconnect the product from the mains power supply
• Check the system periodically, in particular all cables, springs and supports to detect possible imbalances, signs of wear or damage. Do not
use, if repairs or adjustments are necessary, since installation failure or an incorrectly balanced automation may cause injury
• The packing materials of the product must be disposed of in compliance with local regulations
• When operating a biased-off switch, make sure that other persons are kept away from the automation.
• When performing an operation, keep an eye on the automated mechanism and keep all bystanders at a safe distance until the movement
has been completed
• Do not operate the automation if anyone is working on it; disconnect its power supply before permitting such work to be done
• If the power cable is damaged, it must be replaced by the manufacturer or the latter's technical assistance service, or by a similarly qualied
person, in order to prevent any type of risk
INSTALLATION PRECAUTIONS
• Prior to installing the drive motor, check that all mechanical components are in good working order and properly balanced, and that the
automation moves correctly
• Make sure that the controls are at a safe distance from the moving parts, while allowing a good view of them.
Unless a switch is used, the controls should be installed at least 1.5m off the ground and should not be accessible
• If the opening movement is controlled by a re system, make sure that any windows larger than 200mm are closed by the controls
• Make sure that nothing can be trapped between the moving and xed parts during manoeuvres
• Permanently afx the manual operation label next to the manual control
• After installing the drive motor, make sure that the mechanism, protective system and all manual manoeuvres operate properly
To Next Page
Loading...
Need help?
General
