Onkyo R-100 User Manual

Speaker.
Connections
(SPEAKERS)
1.
Connect
the
speakers
to
speaker
terminals.
2.
When
connecting
speakers,
proper
polarity
is
important.
Always
connect
the
(+)
terminal
(red)
on
this
equipment
to
the
(+)
terminal
on
the
speaker
and
the
(—)
terminal
(black)
on
this
equipment
to
the
(—)
terminal
on
the
speaker.
3.
The
load
impedance
of
each
speaker
system
connected
to
this
unit
must
be
at
least
4
ohms.
4.
When
using
only
one
speaker
or
when
you
wish
to
listen
to
monaural,
the
single
speaker
should
never
be
connected
in
parallel
to
both
the
right
and
left
channel
terminals
at
once.
Aliso,
do
not
connect
two
speakers
to
the
same
terminal.
Attach
speaker
cables
to
the
rear
panel
speaker
terminals
with
care,
being
sure
that
connections
are
made
firmly
and
that
there
is
no
possibility
of
a
short
circuit
occurring.
Connecting Speaker Cables
4.
Remove
about
8
mm
of
insulation
from
the
end
of
the
speaker
cable.
2.
Twist
the
exposed
copper
strands
together
tightly.
3..
Unscrew
the
speaker
terminal
part
way
by
turning
it
counter-
clockwise.
4.
Insert
the
exposed
copper
portion
of
the
cable
all
the
way
into
the
opening
in
the
speaker
terminal.
Insert
the
copper
strands
in
the
same
direction
as
that
in
which
the
screw
is
turned.
If
they
are
inserted
in
the
reverse
direction,
they
will
come
out
when
the
screw
is
tightened.
5.
Tighten
the
terminal
screw
by
turning
it
clockwise.
6.
Check
to
make
sure
that
none
of
the
uninsulated
copper
portion
of
the
cable
is
exposed.
CAUTION:
When
using
banana
plugs,
make
sure
the
speaker
terminal
screws
are
screwed
in
firmly
before
inserting
banana
plugs.
Connections
for
Remote
Control
(REMOTE
CONTROL)
A
cassette
tape
deck
and
compact
disc
player
that
have
the
Onkyo
fRI
mark
can
be
operated,
using
the
accessory
remote
control
: Remote Interactive)
transmitter. ( FRI
R-100
COMPACT DISC eee
PLAYER C-100 | °°
CASSETTE
TAPE
fA
REMOTE
DECK
K-100
CONTROL
©
FRI remote
control cable
An
RI
remote
control
cable
equipped
with
a
0.136”
(3.5mm)
diameter
miniature
two-conductor
phone
plug
is
attached
to
compact
disc
player
C-100
and
cassette
tape
deck
K-100,
with
the
FAY
mark.
To
use
an
Onkyo
compact
disc
player
and
cassette
tape
deck
with
the
FI
mark,
insert
the
accessory
remote
control
cable
plug
into
the
REMOTE
CONTROL
jacks.
As
far
as
connecting
sequence
is
concerned,
it
doesn’t
matter
whether
the
cable
is
connected
from
the
R-100
to
the
cassette
tape
deck
or
to
the
compact
disc
player.
The
remote
control
transmitter
is
operated
by
facing
it
towards
the
remote
control
sensor
of
the
R-100.
Remote control operation is not possible when only the remote
Gontrol cable is connected. Remote control cable and connecting |
cable must be connected.
Turntable Connections (PHONO)
Connect the output leads of the turntable to the PHONO jacks.
Be sure to connect the ground (earth) lead wire from the turntable
to the ground terminal (GND): “Lack of proper ground connection
will cause hum. Turntables not provided with GND wires do. not
need to be connected.
1. Place the turntable on a firm shelf or deck free from vibrations
(especially those generated by the speaker system). If the
turntable is permitted to pick up such unwanted vibrations, not
only will the performance of the unit drop, but-distortion in the
bass frequencies and howling in the speakers may also. occur.
Check the turntable instruction manual for any other precautions.
The
loud
noises
that
occur
when
connecting
and
disconnecting
the turntable leads, replacing the cartridge or lowering the
tonearm could damage the speakers. Always turn the power
switch off before making connections.
wn
Compact Disc Player (CD)
Connect
the
output
leads
of
the
CD
player
to
the
CD
jacks.
An
Onkyo
CD
player
with
remote
control
that
has
the
1
mark
can
be
operated
by
the
R-100.
(Please
refer
to
“Connections
for
Remote
Contro!”.)
For
more
details,
refer
to
your
CD
player
instruction
manual.
Tape Deck Connections (TAPE)
Connect
the
tape
deck
output
leads
to
the
PLAY
jacks
and
the
tape
deck
input
leads
to
the
REC
jacks
of
this
unit.
For
more
details,
refer
to
your
tape
deck
instruction
manual.
Video Disc Player (or Video Cassette Player) Connections
(VDP)
Use
the
VDP
jacks.
Connect
the
VIDEO
output
of
the
video
disc
player to the R-100 VDP “VIDEO” jack and the AUDIO output to
the VDP “AUDIO” jacks. The VDP jacks are only for playback, there
is
no
REC
jack.
For
more
details,
refer
to
the
video
disc
player
in-
struction manual.
Video Cassette Recorder Connections (VCR)
41. Connect the VIDEO output of the VCR to the rear panel (VIDEO)
VCR
“IN”
jack
and
the
VIDEO
input
of
the
VCR
to
the
rear
panel
(VIDEO) VCR “OUT” jack. Then connect the AUDIO output
of the VCR to the (AUDIO) VCR L and R “IN” jacks. Finally,
connect the AUDIO input of the VCR to the (AUDIO) VCR L
and R “OUT” jacks.
2. When using a playback-only VCR, only the output connections
need to be performed.
3.
For
more
details,
refer
to
the
VCR
instruction
manual.
Monitor TV Connection
A monitor TV set can be connected to the VIDEO MONITOR OUT
jack.
Processor Jacks
These
jacks
can
be
attached
for
use
with
a
sound
processor
such
as
a
graphic
equalizer.
Be sure to connect the jumper plugs when the processor is not in
use. (No sound will come from the speakers.)

Onkyo R-100 Specifications

General

Brand	Onkyo
Model	R-100
Category	Amplifier
Language	English