EasyManuals Logo

Panasonic KX-TGF370 Series User Manual

Panasonic KX-TGF370 Series
88 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #60 background imageLoading...
Page #60 background image
O
ff: Voice announcement is not
available as alert.
You can configure this setting using either the
base unit or one of the handsets.
Handset / Base unit
1 F
or CELL 1: MMENUN#6031
For CELL 2: MMENUN#6032
2 MbN: Select the desired setting. a
MSAVEN
3 Proceed with the operation for your unit.
Handset: MOFFN
Base unit: MEXITN
Selecting the alert tone
Handset
1 For CELL 1: MMENUN#6041
For CELL 2: MMENUN#6042
2 MbN: Select the desired setting.
3 MSAVEN a MOFFN
Temporary alert off
Y
ou can temporarily disable the alerts by
pressing MAPP ALERTSN.
Base unit
P
ress MAPP ALERTSN to temporarily disable
alerts.
R
is displayed.
R T
o enable alerts again, press MAPP
ALERTSN again.
Using a Bluetooth wireless
h
eadset (optional) for
landline calls
By pairing a Bluetooth headset to the base
unit, you can have a hands-free conversation
wirelessly for landline calls.
Important:
R Your Bluetooth wireless headset must
support the HeadSet Profile (HSP)
specification.
R 1 headset can be paired to the base unit.
R O
nly 2 Bluetooth devices can be used with
the unit at the same time (for example, 2
cellular lines, or the headset and 1 cellular
line).
R For best performance, we recommend
using a Bluetooth headset within 1 m
(3.3 feet) of the base unit. A headset can
communicate with the base unit within a
range of approximately 10 m (33 feet).
Pairing a headset to the base unit
I
mportant:
R Make sure that the Bluetooth headset is not
connected to any other Bluetooth device.
1 Your headset:
Set your headset to pairing mode.
R Refer to the headset operating
instructions.
2 Handset:
MMENUN#621
3 If your headset PIN is “0000”, go to
step 4.
If your headset PIN is other than
0000”, press MCLEARN, then enter your
headset PIN.
R Typically, default PIN is 0000. Refer
to the headset operating instructions.
4 Press MOKN, then wait until a long beep
sounds.
5 MOFFN
R When
is displayed on the base
u
nit, the headset is available for use.
Connecting/disconnecting a headset
I
f you cannot connect the headset and base
unit using the headset, you can connect using
the handset.
To use your headset with another Bluetooth
device such as a cellular phone, you may
need to disconnect it from the base unit.
Important:
R Make sure that the headset is turned on.
Handset
1 T
o connect/disconnect:
MMENUN#622
60
For assistance, visit www.panasonic.ca/english/support
Using Bluetooth® Devices
TG175CSK(en)_0324_ver011.pdf 60 2016/03/24 9:06:21

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Panasonic KX-TGF370 Series and is the answer not in the manual?

Panasonic KX-TGF370 Series Specifications

General IconGeneral
TypeCordless Telephone
Answering SystemYes
Handsets Included1
ExpandableUp to 6 handsets
Caller IDYes
Call BlockYes
Battery TypeNi-MH
DisplayLCD
FrequencyDECT 6.0
Noise ReductionYes
Call WaitingYes
IntercomYes
Conference CallYes
Headset JackYes (2.5mm)
SpeakerphoneYes
Backup BatteryYes
Answering MachineYes

Related product manuals