25
En
03
About Film material
The film material is a video signal with a frame rate of 24 frames/
second. For example, these materials include 1080/24p, 720/24p,
etc.
To output film material
To output 1080/24p film material from HDMI OUT terminals, set the
output video resolution to either Auto, 1080/24p or Source Direct.
Caution
• 1080/24p signals can only be output from the HDMI OUT
terminals. They cannot be output from other video terminals.
•When Auto is selected, the picture is output at 60 frames/
second if your TV is not compatible with 1080/24p signals.
•When 1080/24p or Source Direct is selected, the signals are
output as such, even if your TV is not compatible with 1080/24p
signals. If the picture is not displayed properly, use OUTPUT
RESOLUTION to set an output video resolution at which the
video and audio signals are properly output.
• Even if Auto, 1080/24p or Source Direct is selected, 720/24p
video signals are output at 60 frames/second.
•When 1080/24p is selected, the motion may be unnatural or the
picture may not be clear, depending on the source. In this case,
set the resolution to something other than 1080/24p.
About the output video resolution
The resolution setting and the resolution of the picture that is actually output differ for the different terminals. See the table below.
The table below shows the output video resolution for the different terminals when the frame/field frequency of the playback source is 50 Hz
on the upper line, the resolutions when the source’s frame/field frequency is 60 Hz and 24 Hz on the lower line.
Auto
Output Video Resolution
Source : 1080/24p
Current Output :
1080/24p
Video resolution of the
currently playing disc
Output video resolution
from the player
Example:
Output video
resolution
setting
HDMI MAIN, HDMI SUB
1
1. The video output terminal set at Video in the Setup Navigator (page 20) or the video output terminal selected with VIDEO SELECT (page 24).
COMPONENT/S/VIDEO
1
—
HDMI OUT terminals COMPONENT VIDEO
output terminals
2
2. Depending on the BD, the pictures may not be output.
HDMI OUT terminals COMPONENT VIDEO
output terminals
2
S-VIDEO/
VIDEO output
terminal
2
(TV system)
Auto
3
3. This cannot be selected when the video output terminal is set to COMPONENT/S/VIDEO.
Resolution preferred by
TV
4,5
4. The pictures are output with the preferred output resolution of the device (TV, AV receiver or amplifier, etc.) connected to the selected video output terminal.
However, if devices are connected to both HDMI MAIN and HDMI SUB, the pictures are output with a resolution which both devices support. If the devices
connected to HDMI MAIN and HDMI SUB support different resolutions, turn off the power of the device not being used so that the picture is output with the
optimum resolution for the device to be viewed.
5. For details on the output of film material (1080/24p or 720/24p video signals), see To output film material on page 25.
576/50i
480/60i
— — 576/50i
480/60i
PAL
6
6. Depends on the NTSC on PAL TV setting (page 43).
576i or 480i 576/50i 576/50i 576/50i
480/60i 480/60i 480/60i
576p or 480p 576/50p 576/50p 576/50p
480/60p 480/60p 480/60p
720p 720/50p 576/50p 576/50p
720/60p 720/60p
720/60p
7
7. DVD-Video or DVD VR format may be output at 480/60p. BDs format may be output at 480/60p. At this time, the video signals from the HDMI OUT terminals are
output at the same resolution of 480/60p as the video signals output from the COMPONENT VIDEO terminals.
1080i 1080/50i 576/50p 576/50p
1080/60i 1080/60i
1080/60i
7
1080p
3
1080/50p
8
8. Depending on the connected HDMI cable, the video signals may not be output.
——
1080/60p
8
1080/24p
3
1080/50i — —
1080/24p
5,9,10
9. Depending on the connected TV, the video signals may not be output.
10. Sources recorded in 480/60p, 720/60p or 720/24p are output at 1080/60i.
Source Direct Resolution recorded on
disc
5,9,11
11. 720/24p film material is output at 720/60p.
Resolution recorded on
disc
9,11,12
12. 1080/24p film material is output at 1080/60i.
Resolution recorded on
disc
9,11,12
To Next Page
Loading...
Need help?
General
