EasyManuals Logo
Home>Roland>Electronic Keyboard>V-combo VR-09

Roland V-combo VR-09 Reference Manual

Roland V-combo VR-09
65 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #24 background imageLoading...
Page #24 background image
24
Adding Eects to the Sound
Applying Eects (EFX)
You can apply eects to the sounds you play. This unit contains 7 eect processors; each can be set independently.
For the six eects other than rotary, you can use global control” to conveniently apply each eect in an appropriate way.
MEMO
If you’re playing two sounds (split or dual) (p. 28), the settings will determine which sound is aected.
When using Dual: The same eects will apply to both sounds.
When using Split: The eects will be applied only to the upper part (except for reverb). However if you’ve assigned organ sound to the lower
part, the same eects will apply to all parts.
The eects are connected in the order shown below.
MFX (Multi-eect)Compressor Overdrive Rotary (p. 20)
Tone Delay Reverb
Play
Song
Rhythm pattern
1. Select a sound (p. 13).
MEMO
Some sounds already have eects applied.
The way in which eects are applied will dier depending on the sound.
2. Turn the knobs to adjust the depth of each eect.
* The eects may cause noise or loud sounds. To prevent malfunction and/or
damage to speakers, adjust the volume of external mixers and ampliers.
What’s the global control?
This is technology that optimizes multiple parameters of an eect so that
they can be controlled by a single knob.
Knob Explanation
[OVERDRIVE]
knob
Produces a natural-sounding distortion as heard from a tube amp.
If the knob is turned all the way to the left, no eect will be applied.
Turning the knob toward the right will increase the depth of distortion.
[TONE] knob
Adjusts the tonal character of the low and high frequency ranges.
If the knob is set to the center position, the response will be at.
Turning the knob toward the left will boost the mid-range, making the sound punchier. This is appropriate when playing in a band.
Turning the knob toward the right will boost the low and high-frequency ranges, producing a more colorful sound. This is appropriate for solo
performances.
[COMPRESSOR] knob
Compresses loud sounds and boosts the level of soft sounds.
This narrows the dynamic range, helping to keep your playing audible within the performance of your band.
If you turn the knob all the way to the left, no compressor eect will be applied.
Turning the knob toward the right will smooth out the overall volume, making your sound more consistent.
[MFX] knob
This is a general-purpose multi-eect that can change the fundamental character of the sound, transforming it into something quite dierent.
If you turn the knob all the way to the left, no eect will be applied.
MEMO
The selected type of multi-eect is shown in the bottom line of the display.
To change the multi-eect type, move the cursor to the lower line of the display and turn the [VALUE] dial.
The multi-eect gives you a choice of 20 types. You can use the menu to change the multi-eect type (MFX Type: p. 47).
[DELAY] knob
Produces an echo-like eect by delaying the sound.
By layering the delayed sound with the original sound, you can add depth and spaciousness to the sound.
If you turn the knob all the way to the left, no delay eect will be applied.
Turning the knob toward the right will lengthen the delay time (the time from the original sound until the left and right delay sounds are heard).
MEMO
You can choose from six types of delay. Use the menu to change the delay type (Delay Type: p. 47).
[REVERB] knob
Adds reverberation to the original sound, simulating a spacious room.
If you turn the knob all the way to the left, no reverb eect will be applied.
Turning the knob toward the right will make the reverb deeper.
MEMO
You can use the menu to change the reverb type and the wall type (surface material) (Reverb Type: p. 48, Wall Type: p. 48).
MEMO
When you turn the [DELAY] knob or [REVERB] knob, the type will be displayed. You can turn the [VALUE] dial to change the type.
If you press the [TRANSPOSE] button while the adjustment screen is shown, the adjustment screen will be held. Press the [EXIT] button to return
to the previous screen.

Table of Contents

Other manuals for Roland V-combo VR-09

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Roland V-combo VR-09 and is the answer not in the manual?

Roland V-combo VR-09 Specifications

General IconGeneral
EqualizerYes
Product typeDigital synthesizer
Product colorBlack
Sound effectsCompression, Delay, Overdrive, Reverberation
Sound effects quantity223
Keyboard number of keys61
Maximum polyphony (notes)128
Reverberation effects quantity6
Headphone outputs1
6.35 mm (1⁄4-inch) output2
Battery typeAA
Operating time5 h
Power source typeAC, Battery
Number of batteries supported8
Weight and Dimensions IconWeight and Dimensions
Depth300 mm
Width1008 mm
Height106 mm
Weight5500 g

Related product manuals