Samsung SyncMaster 710MP User Manual

Refer to Specifications > Preset Timing Modes for the resolutions or frequencies that are
supported by the monitor.
Contact the computer dealer or manufacturer for information on Safe Mode Booting.
3. Display Adapter Driver
Display adapter refers to the computer video card driver.
If the adapter is not properly set, you cannot adjust resolution, frequency or color and you cannot
install the monitor driver.
1. Checking Adapter Driver
Click Start
→
Settings
→
Control Panel
→
Display
→
Settings
→
Advanced
→
Adapter.
If "Default" or a wrong product model is indicated, it means that the adapter driver is not properly
installed. Install the adapter driver again according to the information provided by the computer or
video card manufacturers.
2. Installing Adapter Driver
The instructions given below are for general circumstances.
For specific issues, contact the relevant computer or video card manufacturers.
1) Click Start
→
Settings
→
Control Panel
→
Display
→
Settings
→
Advanced
→
Adapter
→
Update Driver
→
Next
→
Display a list of the known drivers for this device so that I can choose
a specific driver
→
Next
→
Have Disk (Insert Video Card Driver diskette)
→
OK
→
Next
→
Next
→
Finish.
2) In case you have Adapter Driver Setup file on your computer:
Run Setup.exe or Install.exe, which is found in the Adapter Driver Setup file.
4. Maintenance and Cleaning
1. Maintaining the Monitor Case.
Clean with a soft cloth after disconnecting the power cord.
2. Maintaining the Flat Panel Display Screen.
Clean with a soft cloth (cotton flannel) smoothly.
z
Do not use benzene, thinner or other flammable substances, or a
wet cloth.
z
Never use acetone, benzene or thinner.
(They may cause flaws or deformation of the screen surface.)
z We recommend a Samsung cleansing agent is used to prevent
damage to the screen.
z
The user will be required to pay costs and related expenses for
repair of damages caused by him/her.
5. Symptoms and Recommended Actions
A monitor recreates visual signals received from the computer. Therefore, if there is trouble with the
computer or the video card, this can cause the monitor to become blank, have poor coloring, noise,
unavailable video mode, etc. In this case, first check the source of the problem, and then contact the
service center or your dealer.
1. Check if the power cord and the video cables are properly connected to the computer.
2. Check if the computer beeps more than 3 times when booting.
(If it does, request an after-service for the main board of the computer.)
3. If you installed a new video card or if you assembled the PC, check if you installed the adapter(video)
driver and the monitor driver.
4. Check if the scanning ratio of the video screen is set at 60Hz.
(The screen refresh rate must be set within in a range of 56~75hz.)
5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove
the Display Adapter at the "
Control Panel
,
System
,
Device Administrator
" and then reboot the
computer to reinstall the adapter (video) driver.

Samsung SyncMaster 710MP Specifications

General

Pixel pitch	0.264 mm
Response time	12 ms
Display diagonal	17 \
Display resolution	1280 x 1024 pixels
Vertical scan range	56 - 75 Hz
Horizontal scan range	31 - 81 kHz
Viewing angle, vertical	140 °
Contrast ratio (typical)	600:1
Display number of colors	16.78 million colors
Viewing angle, horizontal	160 °
Display brightness (typical)	300 cd/m²
Certification	TCO99
Product color	Silver
Market positioning	-
Bandwidth	0.135 GHz
I/O ports	15pin D-sub, S-video, Composite, RF
Power consumption (typical)	43 W
Package weight	6900 g

Weight and Dimensions

Depth (without stand)	206 mm
Width (without stand)	389 mm
Height (without stand)	402 mm
Weight (without stand)	5300 g