english 9
Manufacturer:
Scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear client,
We hope you will enjoy your new Scheppach construction
circular saw and wish you success with it.
The manufacturer of this tool is, according to the current
product liability law, not liable for damages caused to or
by this tool because of:
• incorrectusage,
• failuretoobservethemanual,
• repairsbythirdparties,notauthorizedspecialists,
• ttingandexchangeofnonoriginalexchangeparts,
• nonintendeduse,
• failure of the electrical installations because of
inobservance of the electrical Rules and VDE-Regulations
0100, DIN 57113/VDE0113.
We recommend that you:
Read the entire operating instructions before assembling and
implementing.
This instruction manual should make it easier for you to
get to know your machine and to use its range of applications
as intended. The manual contains important information
on how to work with the machine in a secure, correct and
efficient way, and how you can avoid risks, save repair
costs, reduce down time and increase the reliability and
life span of the machine. Apart from the security rules
mentioned in these operating instructions, you should
implicitly pay attention to the valid regulations of your
country for the use of the machine. Keep the manual, in a
plastic cover protected against dirt and humidity, with the
machine. They should be read and observed carefully by
every member of staff before starting to work. Only people
instructed on how to use the machine and informed about
the possible risks, should be allowed to use it. The required
minimum age is to be adhered to. Besides the safety
instructions in this manual and the special regulations of
your country the recognized technical rules for the operation
of wood processing machines need to be observed.
General instructions
• After unpacking please check all parts for possible
damage during transport. In case of complaints the
driver needs to be contacted as soon as possible.
• Complaints coming in later will not be recognized as
such.
• Checkiftheconsignmentiscomplete.
• Familiarizeyourselfwiththemachinebymeansofthe
operating instructions before implementing it.
• In case of replacing worn or exchange parts, as for
accessories, only use original Scheppach parts. You can
obtain exchange parts at the specialized dealer.
•Uponordering,pleasespecifyourarticlenºsaswellas
type and year of construction of the tool.
Safety instructions
In these operating instructions we have indicated positions
that concern your safety with this mark.
• Forwardthesafetyinstructionstoallpeopleworkingon
or with this machine.
• Themachineisonlytobeusedintechnicallyfaultless
condition as well as according to its intended use, and
in a safety and risk conscious manner, and with
observance of the operation instructions! Especially
malfunctions that can threaten safety have to be repaired
immediately.
• Payattention toall safetyand riskinstructions ofthe
machine.
• Keep all safety and risk instructions of the machine
completely readable.
• Thecircularsawshouldnotbeusedtosawrewood.
• Be careful at work: Danger of damaging nger(s) and
hand(s) by the rotating cutting tool.
• Checkpowersupplylines.
• Donotusedefectivelines.See“Electricalconnection“.
• Pleasebevigilantthemachineissteadfast.
• Pleasepayattentionthattheconstructioncircularsawis
steadfast while being assembled.
• Keepchildrenawayfromthetopowersupplyconnected
machine.
• Theminimumagefortheoperatingpersonis18years.
• Peoplerunningthemachineshouldnotbedistracted.
• Keep the operating site free from wood chips and
waste.
• Payattentiontotherollingdirectionofthemotorand
saw blade. See instructions “Electrical connection“
page U5 (wall mounted connector).
• Buildinonlywellsharpened,slitfreeandnondeformed
saw blades.
• Circularsawbladesmadeoutofhighperformancesteel
should not be built in.
• The security facilities of the machine should not be
dismantled nor be made unusable.
• Theslit wedge isan importantsecurity facility, which
leads the workpiece and avoids the closing of the joints
behind the saw blade and the reversing of the workpiece.
Please note the thickness of the slit wedge – see the
stavedinnºsontheslitwedge.Theslitwedgeshould
not be thinner than the saw blade and not thicker than
its intersection width.
• Putthecoverontheworkpieceateveryoperation.
• Thecovershouldbeputhorizontalabovethesawblade
at every operation.
• Whencuttinglengthwise smallworkpieces–less than
120 mm – implicitly use the spline end.
• Torepairdisordersortopulloutjammedpiecesofwood,
switch the machine off. Pull out power plug!
• Incaseofaknockedoutsawingsplit,renewtheinset.
Pull out power plug!
• Modifyingaswellasadjusting,measuringandcleaning
to be carried out only when motor is switched off. Pull
out power plug!
•Uponleavingtheworkingplace,switchoffthemotor.
Pull out power plug!
To Next Page
Loading...
Need help?
General