www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB
|
23
a.) 90° stop angle (not supplied)
b.) 45° stop angle (not supplied)
c.) Allen key, 6 mm
3. Scope of delivery
• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage.
• If possible, store the packaging until the warranty
period has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, lm and small parts! There is a risk of
swallowing and suffocation!
• Drag, crosscut and mitre Saw
• 1 x Clamping device (8)
• 2 x Workpiece support (9)
• Sawdust bag (21)
• Allen key (c)
• 1x anti-tip
• Operating manual
4. Intended use
The drag, crosscut and mitre saw is designed to
crosscut wood and plastic respective of the ma-
chine’s size. The saw is not designed for cutting
rewood.
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the manufac-
turer will be liable for any damage or injuries of any
kind caused as a result of this.
The equipment is to be operated only with suitable
saw blades. It is prohibited to use any type of cut-
ting-off wheel.
To use the equipment properly you must also ob-
serve the safety information, the assembly instruc-
tions and the operating instructions to be found in
this manual.
All persons who use and service the equipment have
to be acquainted with this manual and must be in-
formed about the equipment’s potential hazards. It
is also imperative to observe the accident prevention
regulations in force in your area. The same applies
for the general rules of health and safety at work.
The manufacturer will not be liable for any changes
made to the equipment nor for any damage resulting
from such changes.
Even when the equipment is used as prescribed it is
still impossible to eliminate certain residual risk fac-
tors. The following hazards may arise in connection
with the machine’s construction and design:
• Contact with the saw blade in the uncovered saw
zone.
• Reaching into the running saw blade (cut injuries).
• Kick-back of workpieces and parts of workpieces.
• Saw blade fracturing.
• Catapulting of faulty carbide tips from the saw
blade.
• Damage to hearing if ear-muffs are not used as
necessary.
• Harmful emissions of wood dust when used in
closed rooms.
Please note that our equipment has not been de-
signed for use in commercial, trade or industri-
al applications. Our warranty will be voided if the
equipment is used in commercial, trade or industrial
businesses or for equivalent purposes.
5. Safety information
Attention! The following basic safety measures must
be observed when using electric tools for protection
against electric shock, and the risk of injury and re.
Read all these notices before using the electric tool
and keep the safety instructions for later reference.
Safe work
1 Keep the work area orderly
– Disorder in the work area can lead to accidents.
2 Take environmental inuences into account
– Do not expose electric tools to rain.
– Do not use electric tools in a damp or wet en-
vironment.
– Make sure that the work area is well-illuminated.
– Do not use electric tools where there is a risk of
re or explosion.
3 Protect yourself from electric shock
– Avoid physical contact with earthed parts (e.g.
pipes, radiators, electric ranges, cooling units).
4 Keep children away
– Do not allow other persons to touch the equip-
ment or cable, keep them away from your work
area.
5 Securely store unused electric tools
– Unused electric tools should be stored in a dry,
elevated or closed location out of the reach of
children.
6 Do not overload your electric tool
– They work better and more safely in the speci-
ed output range.
7 Use the correct electric tool
– Do not use low-output electric tools for heavy
work.
To Next Page
Loading...
Need help?
General
