Sharp R-8680(B) User Manual

OPERATION OF AUTO-TOUCH CONTROL PANEL
Your new Auto-Touch microwave oven uses a microprocessor, the electronic brain that provides the wide
variety of cooking programmes which could not be achieved by conventional control methods.
The operation of the oven is controlled by touching the appropriate pads arranged on the surface of the
control panel. The digital readout will display the cooking time, or time of day. Indicator lights show the
variable cooking setting or cooking function you have programmed. An entry signal tone should be heard
each time you touch the control panel to make a correct entry.
If you do not hear this sound,
1) you have not used enough pressure in touching the pad,
2) you have made more entries than the control panel will accept,
3) you have made an incorrect entry.
In addition to the entry signal tone, an audible signal will sound for approximately 2 seconds at the end
of the cooking cycle.
* Make sure the oven is plugged into a power point 220V AC only. When the oven is plugged in, the
display will show , flashing on and off each second. Touch the (STOP/CLEAR)
pad: will appear.
* You cannot programme the oven if the door is not closed tightly.
* During cooking, the programme cannot be changed until the . (STOP/CLEAR) pad is touched
twice. All functions are locked in to prevent accidental changes.
* If power to the oven is interrupted, the display will intermittently show after the power is
reinstated.
If this occurs during cooking, the programme and the time of day will ke erased. Simply reset the clock
for the correct time of day.
Clock Setting
Touch
the
(STOP/CLEAR)
pad;
[__/:
GG]
will
appear.
After
one
minute
the
display
will
show
a
i 8 .
Suppose you want to enter the correct time of day 12:34. rE Refer to the attached
‘‘Auto-Touch Sheet” A.
Touch the (AUTO START/CLOCK) pad.
Enter the ‘‘hour’’ by touching 10 MIN. pad and 1 MIN. pad.
Then convert ‘hour’ to ‘“‘minute’’ by touching (AUTO START/CLOCK) pad.
Enter the ‘‘minute’’ by touching 10 MIN. pad and 1 MIN. pad.
Touch the (AUTO START/CLOCK) pad.
The clock is now set and will keep the time of day.
NOTE: 1. This is a 12 hour clock. You can enter the clock time from 1:00 to 12:59.
2. If the oven is in cooking or the minute timer mode and you wish to know the time of day, simply
touch the (AUTO START/CLOCK) pad. As long as your finger is touching the
(AUTO START/CLOCK) pad, the time of day will be displayed. This checking opera-
tion does not interfere with cooking time, or minute timer.
oP NS
Minute Timer Setting
The Auto-Touch control panel can be used as a timer for timing up to 99 minutes, 90 seconds. There
is no cooking involved.
Suppose you want to time a 3 minute long distance phone call. - aaa Refer to the attached —
1.
Enter
desired
time.
(3'00‘’)
‘
“‘Auto-Touch
Sheet”
B.
2. Touch the (TIMER/HOLD) pad.
The timer will begin to count down to zero. When the timer reaches zero, the signal will sound. The time
of day will reappear on the display.
To cancel the minute timer during operation, touch the (STOP/CLEAR) pad and the time of day
will reappear.

Sharp R-8680(B) Specifications

Power

AC line voltage	220V, 50Hz
microwave power required	1.3 kW
dual power required	2.8 kW
convection power required	1.6 kW
grill power required	2.6 kW

Output Power

microwave output power	650 W
convection heating element output power	1500 W
grill heating element output power	1000 W

Frequency

microwave frequency	2450 MHz

Capacity

oven capacity	36 litres (1.3 cu.ft.)
turntable tray size	365mm

Weight and Dimensions

outside dimensions	555mm(W) x 380mm(H) x 516mm(D)
cavity dimensions	375mm(W) x 254mm(H) x 385mm(D)
weight	30 kg