TC-Helicon VoiceWorks User Manual

20
SETUP PARAMETERS
BEND RANGE
Sets in semitones the range that MIDI pitch
bend information will alter the pitch of the
harmonies in Notes mode.
N
OTES4CHAN
4 Channel Notes Mode.
Of
f: All harmony voices in Notes Mode will
respond to the base MIDI channel.
On
: In Notes mode, Harmony Voice 1 responds
to the base MIDI channel; Harmony Voice
2 responds to the base MIDI channel +1
etc. All Harmony Voices will respond to
unique MIDI channels.
F
OOTSWITCH 1-2-3
For fully functional footpedal control, use the
Switch-3 three button foot pedal (other 3 but-
ton footswitches may work also). Each button
can be assigned to a special function. The
footswitch assignment options are listed below
and can be applied to each of the three but-
tons.
None Ignore this button.
SS+/-
Increment/Hold:
Press and release: Increments
(changes on release).
Press and hold: After pressing for 2
seconds it will start to decrement.
In Song Mode this changes the Song
Step.
In Recall Mode this changes the
current Preset number.
SS+ Song Mode: Increment Song Step
Recall Mode: Increment current
preset.
SS-
Song Mode: Decrement Song Step
Recall Mode: Decrement current
preset.
Byp
Bypass
Ef
fL Effect toggle mute - latched
Ef
fM
Effect toggle mute - momentary
(effects are on only when the pedal is
pressed)
HarL
Harmony toggle mute
HarM Harmonies toggle mute - momentary
(harmonies are on only when the pedal
is pressed)
Hsus
Harmony Hold.
GLOBAL EFF
Global Effects. This makes the effect
parameters of the chosen preset global for all
recalled presets.
T
UNING
Sets the tuning reference based on A-440.
MIDI Parameters
MIDI CHANNEL
Sets the base MIDI Send and Receive
channel.
MIDI
FILTER
With this parameter you can cause the
VoiceWorks to ignore certain MIDI commands
and data.
P
ignore program changes.
SX
ignore system exclusive messages.
P+SX
ignore program changes and system
exclusive messages.
SYSEX ID
This parameter sets the MIDI sysex ID for the
VoiceWorks.
K
EYBOARD ZONE
This parameter defines the note range of a
MIDI keyboard that the VoiceWorks will
recognize when creating harmonies.
For Example:
Above
C4- would specify that the VoiceWorks
would respond only to MIDI notes
above C4 on the Keyboard.
V
IB
CONTROL
Vibrato Control. This control sets whether the
vibrato follows the onset and attack of the
model (Boost
) or is instantaneous (Manual).
The Mod Wheel on most keyboards controls
the vibrato in both modes, boosting the preset
value in the Boost setting and starting from a
value of 0 in the Manual Setting for full manual
control.
N
OTES TRANS
Notes Mode Transpose. This transposes the
harmony voices in notes mode. The value
corresponds to octaves. This is useful when
used in conjunction with Keyboard Zone.

TC-Helicon VoiceWorks Specifications

Analog Inputs

impedance balanced	3.6 kOhm
impedance unbalanced	1.8 kOhm
line input level at 0 dBFS	24 dBu to 0 dBu
line sensitivity at 12 dB headroom	-12 dBu to 12 dBu
mic input level at 0 dBFS pad off/on	-14 dBu/6 dBu to -51 dBu/-31 dBu
mic sensitivity at 12 dB headroom pad off/on	-26 dBu/-6 dBu to -63 dBu/-43 dBu

Analog Outputs

output impedance	40 Ohm
max output level balanced	20 dBu
max output level unbalanced	14 dBu
output range	Variable up to +20 dBu

Environment

operating temperature	32° F to 122° F (0° C to 50° C)
storage temperature	-22° F to 167° F (-30° C to 70° C)
humidity	Max. 90 % non-condensing

Power

mains voltage	100 to 240 VAC, 50 to 60 Hz (auto-select)
power consumption	<15 W
frequency response DIO	DC to 22/23.9 kHz ± 0.01 dB @ 44.1/48 kHz

Physical Characteristics

dimensions	19" x 1.75" x 8.2" (483 x 44 x 195 mm)
weight	4.1 lb. (1.85 kg)
display	16x 2 character LCD display