Vector START-IT VEC022DSCC User Manual

4
CAUTION: Caution statements advise against certain conditions and practices
that may result in damage to vehicles, appliances and/or the Jump-
Starter.
IMPORTANT:
Although this unit is delivered in a partially charged state, you must fully charge it
with the supplied 110/120 Volt AC charger for a full 24 hours before using it for
the first time. You cannot overcharge the unit using the AC charger method.
1. Use only the supplied cords/adapters for recharging this unit. Do not recharge
for more than 3-4 hours maximum using 12 Volt DC method. Recharge unit
after each use.
2. All On/Off switches should be in the OFF position when the unit is charging
or not in use. Make sure all switches are in the OFF position before connection
to a power source or load.
3. Never insert anything other than the supplied power/recharging cords or
recommended appliance power/recharging cords into the 12 Volt DC
charging/power outlet on this unit. Do not use any accessory that is not
recommended or provided by the manufacturer.
4. Do not use this unit to operate appliances that draw more than 5 amps.
5. This system is designed to be used only on vehicles with 12 Volt DC battery
systems. Do not connect to a 6 Volt or 24 Volt battery system.
6. This system is not designed to be used as a replacement for a vehicular battery.
Do not attempt to operate a vehicle that does not have a battery installed.
7. Vehicles that have on-board computerized systems may be damaged if vehicle
battery is jump-started. Before jump-starting, read the vehicle’s owners
manual to confirm that external-starting assistance is advised.
8. Excessive engine cranking can damage a vehicle’s starter motor. If the engine
fails to start after the recommended number of attempts, discontinue jump-start
procedures and look for other problems that may need to be corrected.
9. Although this unit contains a non-spillable battery, it is recommended that unit
be kept upright during storage, use and recharging. To avoid possible damage
that may shorten the unit’s working life, protect it from direct sunlight, direct
heat and/or moisture.
10. Check unit periodically for wear and tear. Replace worn or defective parts
immediately. Contact Vector Customer Service department toll-free
866-584-5504.
11. Do not attempt to jump-start a frozen battery.
12. Never submerge this unit in water.
13. DO NOT over-inflate tires.

Vector START-IT VEC022DSCC Specifications

Battery

battery type	sealed, lead-acid, rechargeable, maintenance-free, 12 volt DC
boost ampere	450 instantaneous cranking amps

Charging Adapters

DC charging adapter	12 volt DC
AC charging adapter	110/120 volt AC (700mA, 12 volt DC output)
accessory outlet	self-resetting breaker 5 amps DC

Booster Cables

booster cables	heavy duty cable
copper clamps	450 amp

Lighting

area light	cold cathode fluorescent lamp (CCFL)

Summary

SAFETY INFORMATION

1. INTRODUCTION

2. FRONT PANEL

Indicators

Explains the meaning of various LED and display indicators on the front panel.

Function Modes

Details the operation of different function buttons and modes on the unit.

3. JUMP-START SYSTEM

3.1 JUMP-STARTING INSTRUCTIONS

Provides step-by-step guidance for safely jump-starting a vehicle.

4. CHARGING/RECHARGING

4.1 110/120 VOLT AC CHARGING

Details the procedure for recharging the unit using a standard AC wall outlet.

4.2 12 VOLT DC CHARGING

Explains how to recharge the unit using a vehicle's 12V DC accessory outlet.

4.3 REPLACE FUSE

Instructions on how to replace the fuse in the DC charging adapter plug.

4.4 ESTIMATED BATTERY LIFE

Provides estimated battery life based on usage and recharge cycles.

5. OPERATION AS A 12 VOLT PORTABLE POWER SUPPLY

6. AREA LIGHT

7. AIR COMPRESSOR/TIRE INFLATOR

7.1 WARNINGS FOR COMPRESSOR USE

Important safety precautions to follow when using the air compressor.

7.2 TIRE INFLATION OR PRODUCTS WITH A VALVE STEM

Step-by-step guide for inflating tires and items with valve stems.

7.3 INFLATING OTHER ARTICLES (WITHOUT VALVE STEM)

Instructions for inflating items like balls using adapter nozzles.

7.4 TYPICAL INFLATION TIMES

Approximate times required to inflate various items using the compressor.

8. REPLACEMENT PARTS

8.1 BATTERY REPLACEMENT

Information and recommendations for replacing the unit's internal battery.

8.2 BATTERY DISPOSAL:

Guidance on the proper recycling and disposal of the unit's battery.

9. SPECIFICATIONS