To Next Page

To Previous Page

D-302754 23

Report Cnfrm Alarm [Fig 4.5.3(25)] - see note in Fig.

4.5

Here you determine whether the system will report

whenever 2 or more events (confirmed alarm) occur

during a specific period (see par. 4.4.33).

Available

options are: enable report, disable report,

enable + bypass (enabling report and bypassing the

detector - applicable to PowerMaxComplete that is

compatible with DD243 standard).

Recent Close [Fig 4.5.3(26)]

Here you enable or disable the “recent closing” report, that is

sent to the central station if an alarm occurs within 2 minutes

from the expiry of the exit delay.

The options are: recent close ON and recent close OFF.

Zone restore [Fig 4.5.3(27)]

Here you determine whether a zone restore will be

reported or not.

The options are: report restore and don't report.

System Inactivity Report [Fig 4.5.3(28)]

Here you determine whether the central station will receive

a message if the system is inactive (not armed) during a

defined period (days).

The options are: disable, rep. after 7d, rep. after 14d,

rep. after 30d, rep. after 90d.

Call Waiting OFF [Fig 4.5.3(29)]

Here you enter a code to cancel "call waiting" when calling

the central station.

4.5.4 Private Report (Fig. 4.5)

Report To Private [Fig 4.5.4(1)]

Here you determine which event groups will be reported to

private telephone subscribers. The options are as follows:

Term Description

all All messages

all (-op/cl) All messages, except open/close

all (-alerts) All messages, except alerts

alarms Alarm messages

alerts Alert messages

op/cl Open/close

disable report No message will be reported

Note: “All” means all events including the L. BAT and AC

FAIL trouble messages.

Voice report [Fig 4.5.4(2)]

Private Tel# [Fig 4.5.4(2a)]

Here you program the 1

telephone number (including

area code, if required) of the private subscriber to which

the system will report the event groups defined in Report

To Private.

Private Tel# [Fig 4.5.4(2b)]

Here you program the 2

telephone number (including

area code, if required) of the private subscriber to which

the system will report the event groups defined in Report

To Private.

Private Tel# [Fig 4.5.4(2c)]

Here you program the 3

telephone number (including

area code, if required) of the private subscriber to which

the system will report the event groups defined in Report

To Private.

Private Tel# [Fig 4.5.4(2d)]

Here you program the 4

telephone number (including area

code, if required) of the private subscriber to which the system

will report the event groups defined in Report To Private.

Redial Attempts [Fig 4.5.4(2e)]

Here you determine the number of times the communicator

will dial the called party’s number (private telephone).

The options are: 1, 2, 3 and 4 attempts.

Attention! A maximum of 2 dialing attempts is permitted

by the Australian Telecommunication Authority.

Two-Way Voice - Private Phones [Fig 4.5.4(2f)]

Here you determine whether 2-way voice communication

with private telephones will be allowed or not.

The options are: enable 2-way and disable 2-way.

Tel. acknowledge [Fig 4.5.4(2g)]

Here you determine whether the system will use the

single acknowledge

or the all acknowledge mode when

reporting to private telephones.

Note: In the single acknowledge

mode, receiving an

acknowledge signal from a single telephone is sufficient to

consider the current event closed and call off the

communication session. The remaining telephones serve

for backup purposes only. In the all acknowledge

mode, an

acknowledge signal must be received from each telephone

before the current event is considered reported.

The options are: single ack and all ack.

SMS Report Tel# [Fig 4.5.4(3)]

SMS Tel# [Fig 4.5.4(3a)]

Here you define the first SMS phone number (including

area code, 16 digits maximum) to which pre-selected

event types will be reported.

SMS Tel# [Fig 4.5.4(3b)]

Here you define the second SMS phone number (including

area code, 16 digits maximum) to which pre-selected

event types will be reported.

SMS Tel# [Fig 4.5.4(3c)]

Here you define the third SMS phone number (including

area code, 16 digits maximum) to which pre-selected

event types will be reported.

SMS Tel# [Fig 4.5.4(3d)]

Here you define the fourth SMS phone number (including

area code, 16 digits maximum) to which pre-selected

event types will be reported.

Brand	Visonic
Model	POWERMAXCOMPLETE - INSTALLER GUIDE
Category	Security System
Language	English

Visonic POWERMAXCOMPLETE - INSTALLER GUIDE User Manual

Table of Contents

Questions and Answers:

Visonic POWERMAXCOMPLETE - INSTALLER GUIDE Specifications

Related product manuals