ABB ACS255 User Manual

33
8. Application Macros
8.1. Overview of macros
Application macros are pre-programmed parameter sets. While starting up the drive, the user selects the macro best suited for the
purpose with parameter 9902 DIGITAL INPUTS FUNCTION SELECT and 1103 PRIMARY COMMAND SOURCE MODE.
The term “Selected Speed Reference” in the table below is determined by the value set in 1103 PRIMARY COMMAND SOURCE MODE.
1103 (control Mode)
Selected Speed Reference
0 : Terminal Mode
Analog input 1
1 : Keypad Mode (uni-directional)
Digital Potentiometer
2 : Keypad Mode (bi-directional)
Digital Potentiometer
3 : User PI mode
PI controller output
4 : Fieldbus Control
Speed reference via Fieldbus
5 : CANopen
Speed reference via CANopen
11
O: Stop
C: Run Fwd
O: Stop
C: Run Rev
O: Selected Speed Ref
C: Preset speed 1, 2
Analog 1 Speed reference
O: Preset speed 1
C: Preset speed 2
12
O: Stop
C: Run Fwd
O: Stop
C: Run Rev
Digital input 3
Analog input 1
Analog input 2
Preset Speed
Off
Off
Off
Preset Speed 1
On
Off
Off
Preset Speed 2
Off
On
Off
Preset Speed 3
On
On
Off
Preset Speed 4
13
O: Stop
C: Run Fwd
O: Stop
C: Run Rev
O: Selected Speed Ref
C: Preset speed 1
Analog 1 Speed reference
Analog torque reference
14
O: Stop
C: Run Fwd
O: Stop
C: Run Rev
O: Selected Speed Ref
C: Preset speed 1
Analog 1 Speed reference
O: Decel ramp 1 (Par 2203)
C: Decel ramp 2 (Par 2206)
1)
15
O: Stop
C: Run Fwd
O: Stop
C: Run Rev
O: Selected Speed Ref
C: Analog input 2
Analog 1 Speed reference
Analog 2 Speed reference
16
O: Stop
C: Run Fwd
O: Stop
C: Run Rev
O: Selected Speed Ref
C: Preset speed 1
Analog 1 Speed reference
External trip
2)
O: trip C: Run
17
O: Stop
C: Run Fwd
O: Stop
C: Run Rev
Digital input 3
Analog input 1
Preset Speed
External trip
2)
O: trip C: Run
Off
Off
Preset Speed 1
On
Off
Preset Speed 2
Off
On
Preset Speed 3
On
On
Preset Speed 4
18
O: Stop
C: Run Fwd
O: Stop
C: Run Rev
Digital input 3
Analog input 1
Preset Speed
O: Decel ramp 1 (Par 2203)
C: Decel ramp 2 (Par 2206)
1)
Off
Off
Preset Speed 1
On
Off
Preset Speed 2
Off
On
Preset Speed 3
On
On
Preset Speed 4
9902
Digital Input 1
(Terminal 2)
Digital Input 2
(Terminal 3)
Digital Input 3
(Terminal 4)
Analog Input 1
(Terminal 6)
Analog Input 2
(Terminal 10)
1
O: Stop
C: Run
O: Forward
C: Reverse
O: Selected Speed Ref
C: Preset speed 1, 2
Analog 1 Speed reference
O: Preset speed 1
C: Preset speed 2
2
O: Stop
C: Run
O: Forward
C: Reverse
Digital input 3
Analog input 1
Analog input 2
Preset Speed
Off
Off
Off
Preset Speed 1
On
Off
Off
Preset Speed 2
Off
On
Off
Preset Speed 3
On
On
Off
Preset Speed 4
3
O: Stop
C: Run
O: Forward
C: Reverse
O: Selected Speed Ref
C: Preset speed 1
Analog 1 Speed reference
Analog torque reference
4
O: Stop
C: Run
O: Forward
C: Reverse
O: Selected Speed Ref
C: Preset speed 1
Analog 1 Speed reference
O: Decel ramp 1 (Par 2203)
C: Decel ramp 2 (Par 2206)
1)
5
O: Stop
C: Run
O: Forward
C: Reverse
O: Selected Speed Ref
C: Analog input 2
Analog 1 Speed reference
Analog 2 Speed reference
6
O: Stop
C: Run
O: Forward
C: Reverse
O: Selected Speed Ref
C: Preset speed 1
Analog 1 Speed reference
External trip
2)
O: trip C: Run
7
O: Stop
C: Run
O: Forward
C: Reverse
Digital input 3
Analog input 1
Preset Speed
External trip
2)
O: trip C: Run
Off
Off
Preset Speed 1
On
Off
Preset Speed 2
Off
On
Preset Speed 3
On
On
Preset Speed 4
8
O: Stop
C: Run
O: Forward
C: Reverse
Digital input 3
Analog input 1
Preset Speed
O: Decel ramp 1 (Par 2203)
C: Decel ramp 2 (Par 2206)
1)
Off
Off
Preset Speed 1
On
Off
Preset Speed 2
Off
On
Preset Speed 3
On
On
Preset Speed 4
9
O: Stop
C: Run
O: Forward
C: Reverse
Digital input 3
Analog input 1
Preset Speed
O: Selected Speed Ref
C: Preset speed 1 .. 4
Off
Off
Preset Speed 1
On
Off
Preset Speed 2
Off
On
Preset Speed 3
On
On
Preset Speed 4
10
O: Stop
C: Run
O: Forward
C: Reverse
Normally Open (N.O.)
Close to increase speed
Normally Open (N.O.)
Close to reduce speed
O: Selected Speed Ref
C: Preset speed 1

ABB ACS255 Specifications

General

Brand	ABB
Model	ACS255
Category	Controller
Language	English