EasyManuals Logo
Home>ABB>Valve Positioners>TZIDC

ABB TZIDC User Manual

ABB TZIDC
88 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #40 background imageLoading...
Page #40 background image
Specifications
40 TZIDC, TZIDC-110, TZIDC-120 42/18-84-EN
9 Specifications
Change from one to two colu mns
9.1 TZIDC
9.1.1 Input
Setpoint signal (two-wire technology)
Nominal range 4 ... 20 mA
Split range configuration between 20 ... 100 %
of the nominal range
Max. 50 mA
Min. 3.6 mA
Starting at 3.8 mA
Load voltage at 20 mA 9.7 V
Impedance at 20 mA 485
Digital input
Control voltage 0 ... 5 V DC
logical switching state "0"
11 ... 30 V DC
logical switching state "1"
Current max. 4 mA
9.1.2 Output
Compressed air output
Range 0 ... 6 bar (0 ... 90 psi)
Air capacity
5.0 kg/h = 3.9 Nm
3
/h = 2.3 sfcm
at 1.4 bar (20 psi) supply pressure
13 kg/h = 10 Nm
3
/h = 6.0 sfcm
at 6 bar (90 psi) supply pressure
Output function For single or double-acting
actuators, air is vented from
actuator or actuator is blocked in
case of (electrical) power failure
Shut-off values
End position 0 % = 0 ... 45 %
End position 100 % = 55 ... 100 %
Digital output (control circuit to DIN 19234 / NAMUR)
Supply voltage
5 ... 11 V DC
Current > 0.35 mA … < 1.2 mA
Switching state logical "0"
Current > 2.1 mA
Switching state logical "1"
Effective direction (configurable)
normally logical "0" or logical "1"
9.1.3 Travel
Rotation angle
Used range 25 ... 120° (rotary actuators,
optional 270°)
25 ... 60 ° (linear actuators)
Travel limit Min. and max. limits, freely
configurable between
0 ... 100 % of total travel (min.
range > 20 %)
Travel time prolongation Range of 0 ... 200 s, separately
for each direction
Dead band time limit Setting range 0 ... 200 s
(monitoring parameter for
control until the deviation
reaches the dead band)
9.1.4 Air supply
Instrument air free of oil, water and dust to DIN/ISO
8573-1. Pollution and oil content
according to Class 3 (purity: max.
particle size = 5 µm, max. particle density
= 5 mg / m
3
; oil content: max.
concentration = 1 mg / m
3
; pressure dew
point: 10 K below operating temperature)
Supply pressure 1.4 ... 6 bar (20 ... 90 psi)
IMPORTANT (NOTE)
Do not exceed the maximum operating pressure of the
actuator!
Air consumption < 0.03 kg/h / 0.015 scfm (independent
of supply pressure)

Table of Contents

Other manuals for ABB TZIDC

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the ABB TZIDC and is the answer not in the manual?

ABB TZIDC Specifications

General IconGeneral
BrandABB
ModelTZIDC
CategoryValve Positioners
LanguageEnglish

Related product manuals