Ariston ALTEAS ONE+ NET User Manual

TECHNICAL AREA
/ 47
5 ZONE 2 PARAMETERS
5. 0 SETPOINT
5. 0. 2 T set Zone 2 from 35 to 82 (°C)
(high temperature)
70
from 20 to 45 (°C)
(low temperature)
25
To set only with Fixed Flow Temperaure of
Thermoregulation (see 521)
5. 2 ZONE 2 SETTING
5. 2. 0 Zone 2 Temperature
range
0 = from 20 to
45°C
(low temperature)
1 = from 35 to 82°C
(high temperature)
1
5. 2. 1 Thermoregulation
To enabled
thermoregulation press
Auto button.
On the dispaly will
appear the symbol
AUTO
0 = Fixed Flow
Temperature
1 = Basic
Thermoregulation
2 = Room Temp
only
3 = Outdoor Temp.
only
4 = Room +
outdoor Temp.
1
5. 2. 2 Slope from 1.0 to 3.5
(high temperature)
1.3
from 0.2 to 1.0
(low temperature)
0.6
See parameter 422
Only enabled when an outdoor sensor is instal-
led
When an outdoor sensor is used, the boiler
calculates the most suitable delivery
temperature, taking into account the outside
temperature and type of system. The type of
curve should be selected in correspondence with
the projected temperature of the system and the
nature of the dispersions present in the structure.
For high-temperature systems, one of the curves
depicted below may be chosen.
5. 2. 3 Offset
Auto Function active
from - 14 to + 14 (°C)
(high temperature)
0
from - 7 to + 7 (°C)
(low temperature)
0
To adapt the heating curve to the system
requirements, shift the curve in parallel so that
the calculated ow temperature is modied, in
addition to the room temperature.
By accessing the parameter and pressing the
button b, it is possible to shift the curve in a
parallel direction. The shifting value can be read
on the display: from -14 to +14 for high-temperature
devices, or from -7 to 7 for low-temperature
devices. Each step corresponds to a 1°C increase/
decrease In the ow temperature with respect to
the set-point value.
menu sub-menu parameter description value default setings menu sub-menu parameter description value default setings
5. 2. 4 Room Inuence
Proportional
Auto Function active
from 0 to 20 20
If setted = 0 the room temperature doesn’t
inuence the calculation of the set-point.
If setted = 20, the room temperature has the
maximun inuence to calculate the set-point
- only active when the BUS device is connected
5. 2. 5 Maximum CH
Temperature Zone 2
from 35 to 82 °C
(Param. 520 = 1)
82
from 20 to 45 °C
(Param. 520 = 0)
45
5. 2. 6 Minimum CH
Temperature Zone 2
from 35 to 82 °C
(Param. 520 = 1)
35
from 20 to 45 °C
(Param. 520 = 0)
20
5. 3 Z2 DIAGNOSTICS
5. 3. 4 Heat request Zone 2 0 = OFF
1 = ON
6 ZONE 3 PARAMETER
6. 0 SETPOINT
6. 0. 2 T set Zone 3 from 35 to 82 (°C) 70
To set only with Fixed Flow Temperaure of
Thermoregulation (see 521)
6. 2 ZONE 3 SETTING
6. 2. 0 Zone 3 Temperature
range
0 = from 20 to
45°C
(low temperature)
1 = from 35 to 82°C
(high temperature)
1
6. 2. 1 Thermoregulation
To enabled
thermoregulation press
Auto button.
On the dispaly will
appear the symbol
AUTO
0 = Fixed Flow
Temperature
1 = Basic
Thermoregulation
2 = Room Temp
only
3 = Outdoor Temp.
only
4 = Room +
outdoor
Temp.
1
6. 2. 2 Slope from 1.0 to 3.5
(high temperature)
1.3
from 0.2 to 1.0
(low temperature)
0.6
See parameter 422
Only enabled when an outdoor sensor is instal-
led
When an outdoor sensor is used, the boiler
calculates the most suitable delivery
temperature, taking into account the outside
temperature and type of system. The type of
curve should be selected in correspondence with
the projected temperature of the system and the
nature of the dispersions present in the structure.
For high-temperature systems, one of the curves
depicted below may be chosen.

Ariston ALTEAS ONE+ NET Specifications

General

Brand	Ariston
Model	ALTEAS ONE+ NET
Category	Boiler
Language	English