EasyManuals Logo
Home>Cascade>Power Tool>40D

Cascade 40D User Manual

Default Icon
46 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #23 background imageLoading...
Page #23 background image
669224-R5
ROUBLESHOOTING
T
21
4.4-4 Sideshift Circuit
Pressure Test
Iftheclampdoesnotsideshiftrightandleftatequal
speedsordropsaloadwhilesideshifting,oneofthe
sideshiftcheckvalvecartridgesisfaulty.Thetwoouter
cartridgesonthefrontofthevalveareforthesideshift
circuit.
IMPORTANT:Attachmentsequippedwithsolenoid
adaptionmustbeplumbedtothecheckvalvesothe
solenoidwillbeenergizedfortheclamp/openfunctions.
WARNING:Beforeinstallingthepressure
gauge,relievepressureinthehydraulic
system.Turntruckoffandopenthetruck
auxiliarycontrolvalvesseveraltimesinboth
directions.
WARNING:Beforeremovingthepressure
gauge,relievepressureinthehydraulic
system.Turntruckoffandopenthetruck
auxiliarycontrolvalvesseveraltimesinboth
directions.
1 Top Mount Valves –Installthepressuregaugeand
hoseassemblyinthevalvetestportmarked'G',located
onthebackofthevalvebody.
Center Mount Valves –Removethebumper.Install
ateetting,hoseandgaugebetweenthecylinderrod
endsupplyhoseandteetting.
2 Startthetruck.Clampontoaload(liftnomorethan1
in.(25mm)oftheoor).HoldtheSIDESHIFTcontrol
handleinthesideshiftleftpositionforafewseconds.
3 Returnthehandletoneutral.Watchthegaugepressure
reading.
• Ifthepressure dropsmorethan150psi(10bar)
initiallyandadditionaldropexceeds25psi(2bar)
perminute,thesideshiftleftcartridgeisfaultyand
requireservice.RefertoSection5.5-3.
• Ifthepressure does not dropmorethan150psi
(10bar)initiallyandanadditionaldropdoesnot
exceed25psi(2bar)perminute,movethesideshift
controlhandleinthesideshiftrightpositionforafew
seconds.Continuewithtroubleshootingprocedure.
4 Returnthehandletoneutral.Watchthegaugepressure
reading.
• Ifthepressure dropsmorethan150psi(10bar)
initiallyandadditionaldropexceeds25psi(2bar)
perminute,thesideshiftrightcartridgeisfaultyand
requiresservice.RefertoSection5.5-3.
• Ifthepressure does not dropmorethan150
psi(10bar)initiallyandadditionaldropdoesnot
exceed25psi(2bar)perminute,theproblemisnot
hydraulic.
CL2229.eps
CL2230.eps
CL2226.eps
Installtting,hose
andgauge
Installtting,hose
andgauge
SideshiftRight
Cartridge
SideshiftRight
Cartridge
Clamp
Cartridge
Clamp
Cartridge
SideshiftLeft
Cartridge
SideshiftLeft
Cartridge
Top Mount
Valves
Center Mount
Valves

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cascade 40D and is the answer not in the manual?

Cascade 40D Specifications

General IconGeneral
BrandCascade
Model40D
CategoryPower Tool
LanguageEnglish

Related product manuals