Casio XJ-V1 User Manual

28
Warning messages and indicators let you know what the problem is when a projector error occurs.
z When an error occurs, wait until the fan stops before unplugging the AC power cord. If you unplug
the AC power cord while the fan is still operating, an error may occur when you plug the AC power
cord back in.
z Press the [ESC] key to clear the warning message.
Error Indicators and Warning Messages
Indicator/Error Message Description and Required Action
POWER : Green steady The projector’s internal temperature is very high. Perform the following
steps.
1 Check for any blocking of the projector’s intake vents and exhaust
vents, and make sure that there is sufficient space around the
projector. See
“Setup Precautions” (page 6).
2 If there is dust accumulated around the intake vents and/or exhaust
vents, turn off the projector and remove it. See
“Cleaning the
Projector” (page 26).
STATUS : – (Green steady when
“On” is selected for the
“Eco Mode” setting.)
Message : Internal temperature is too
high. Check projector air
vents for blockage.
POWER : Green steady J
Red steady
Power has turned off automatically due to internal overheating. Perform
the following steps.
1 Check for any blocking of the projector’s intake vents and exhaust
vents, and make sure that there is sufficient space around the
projector. See
“Setup Precautions” (page 6).
2 If there is dust accumulated around the intake vents and/or exhaust
vents, remove it. See
“Cleaning the Projector” (page 26).
If there is no problem with the projector’s vents, confirm that the POWER/
STANDBY indicator is lit red (without flashing), and then turn power back
on again. If the error occurs again when you turn power back on, contact
your retailer or nearest authorized CASIO Service Center.
STATUS : –
Message : Internal temperature is too
high. The projector will
turn off.
POWER : Red steady Power has turned off automatically due to a fan problem. Confirm that the
POWER/STANDBY indicator is lit red (without flashing) and that the fan
has stopped. After checking the POWER/STANDBY indicator, disconnect
the power cord from the projector and wait for all of the projector’s
indicators to go out. Next, reconnect the power cord and turn projector
power back on.
If the error occurs again when you turn power back on, contact your
retailer or nearest authorized CASIO Service Center.
STATUS : Amber flashing
(0.5-second interval)
Message : There is a problem with
the fan. The projector will
turn off.
POWER : Green steady A system problem has occurred, which may cause problems with some
functions. Turn off the projector, disconnect the power cord from the
projector and wait for all of the projector’s indicators to go out. Next,
reconnect the power cord and turn the projector back on.
If the error occurs again when you turn power back on, contact your
retailer or nearest authorized CASIO Service Center.
STATUS : – (Green steady when
“On” is selected for the
“Eco Mode” setting.)
Message : There is some problem
with the system.
The audio function may
not operate correctly.
POWER : Red steady The projector was turned off automatically due to some problem that was
probably caused by external digital noise or some other reason. Confirm
that the POWER/STANDBY indicator is lit red (without flashing). After
checking the POWER/STANDBY indicator, disconnect the power cord
from the projector and wait for all of the projector’s indicators to go out.
Next, reconnect the power cord and turn projector power back on.
If the error occurs again when you turn power back on, contact your
retailer or nearest authorized CASIO Service Center.
STATUS : Red steady
Message : –

Casio XJ-V1 Specifications

General

Matrix size	0.55 \
Number of colors	1.073 billion colors
Native aspect ratio	-
Projection distance	- m
Projection technology	DLP
Contrast ratio (dynamic)	20000:1
Screen size compatibility	30 - 300 \
Projector native resolution	XGA (1024x768)
Keystone correction, vertical	-30 -30 °
Focus	Manual
Offset	72 %
Throw ratio	1.54 - 1.71:1
Optical zoom	1.1 x
Focal length range	- mm
Light source type	Laser/LED hybrid
Service life of light source	20000 h
Full HD	No
Supported graphics resolutions	1200 x 1600, 1680 x 1056
AC (power) in	Yes
Composite video in	0
USB connector type	Micro-USB B
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Noise level	37 dB
Noise level (economic mode)	35 dB
Placement	Desktop
Product type	Standard throw projector
Product color	White
Power source	AC
Power consumption (standby)	0.23 W
Power consumption (typical)	150 W
Operating temperature (T-T)	5 - 35 °C
Remote control type	IR

Weight and Dimensions

Width	270 mm
Height	89 mm
Weight	2800 g