Danfoss VLT AutomationDrive FC 300 Programming Guide

[5] Torque limit Torque limit [5] The torque limit, set in par. 4-16 Torque Limit Motor Mode or par. 4-17 Torque
Limit Generator Mode
, has been exceeded.
[6] Current limit
Current limit [6] The motor current limit, set in par. 4-18 Current Limit , has been exceeded.
[7] Out of current range
Out of current range [7] The motor current is outside the range set in par. 4-18 Current Limit .
[8] Below I low
Below I low [8] The motor current is lower than set in par. 4-50 Warning Current Low .
[9] Above I high
Above I high [9] The motor current is higher than set in par. 4-51 Warning Current High .
[10] Out of speed range
Out of speed range [10] The speed is outside the range set in par. 4-52 Warning Speed Low and
par. 4-53
Warning Speed High .
[11] Below speed low
Below speed low [11] The output speed is lower than the setting in par. 4-52 Warning Speed Low .
[12] Above speed high
Above speed high [12] The output speed is higher than the setting in par. 4-53 Warning Speed
High
.
[13] Out of feedb. range
Out of feedb. Range [13] The feedback is outside the range set in par. 4-56 Warning Feedback
Low
and par. 4-57 Warning Feedback High .
[14] Below feedb. low
Below feedb. Low [14] The feedback is below the limit set in par. 4-56 Warning Feedback Low .
[15] Above feedb. high
Above feedb. High [15] The feedback is above the limit set in par. 4-57 Warning Feedback High .
[16] Thermal warning
Thermal warning [16] The thermal warning turns on when the temperature exceeds the limit in the
motor, the frequency converter, the brake resistor or the thermistor.
[17] Mains out of range
Mains out of range [17] The mains voltage is outside the specified voltage range.
[18] Reversing
Reversing [18] The output is high when the frequency converter is running counter clockwise (the
logical product of the status bits “running” AND “reverse”).
[19] Warning
Warning [19] A warning is active.
[20] Alarm (trip)
Alarm (trip) [20] A (trip) alarm is active.
[21] Alarm (trip lock)
Alarm (trip lock) [21] A (Trip lock) alarm is active.
[22] Comparator 0
Comparator 0 [22] Use the result of comparator 0.
[23] Comparator 1
Comparator 1 [23] Use the result of comparator 1.
[24] Comparator 2
Comparator 2 [24] Use the result of comparator 2.
[25] Comparator 3
Comparator 3 [25] Use the result of comparator 3.
[26] Logic rule 0
Logic rule 0 [26] Use the result of logic rule 0.
[27] Logic rule 1
Logic rule 1 [27] Use the result of logic rule 1.
[28] Logic rule 2
Logic rule 2 [28] Use the result of logic rule 2.
[29] Logic rule 3
Logic rule 3 [29] Use the result of logic rule 3.
[33] Digital input DI18
Digital input DI18 [33] Use the result of digital input 18.
[34] Digital input DI19
Digital input DI19 [34] Use the result of digital input 19.
[35] Digital input DI27
Digital input DI27 [35] Use the result of digital input 27.
[36] Digital input DI29
Digital input DI27 [35] Use the result of digital input 29.
[37] Digital input DI32
Digital input DI32 [37] Use the result of digital input 32.
[38] Digital input DI33
Digital input DI33 [38] Use the result of digital input 33.
[39] Start command
Start command [39] A start command is issued.
[40] Drive stopped
Drive stopped [40] A stop command ( Jog, Stop, Qstop, Coast) is issued – and not from the SLC
itself.
FC 300 Programming Guide 3 Parameter descriptions
MG.33.M8.02 - VLT
®
is a registered Danfoss trademark 177
3

Danfoss VLT AutomationDrive FC 300 Specifications

General

Brand	Danfoss
Model	VLT AutomationDrive FC 300
Category	DC Drives
Language	English