Danfoss VLT AutomationDrive FC 300 Programming Guide

If the set-up is changed, it will merge with other set-up commands coming from either the digital
inputs or via a fieldbus.
[10] Select preset ref 0
Select preset reference 0 [10] – selects preset reference 0.
If the active preset reference is changed, it will merge with other preset reference commands com-
ing from either the digital inputs or via a fieldbus.
[11] Select preset ref 1
Select preset reference 1 [11] – selects preset reference 1.
If the active preset reference is changed, it will merge with other preset reference commands com-
ing from either the digital inputs or via a fieldbus.
[12] Select preset ref 2
Select preset reference 2 [12] – selects preset reference 2.
If the active preset reference is changed, it will merge with other preset reference commands com-
ing from either the digital inputs or via a fieldbus.
[13] Select preset ref 3
Select preset reference 3 [13] – selects preset reference 3.
If the active preset reference is changed, it will merge with other preset reference commands com-
ing from either the digital inputs or via a fieldbus.
[14] Select preset ref 4
Select preset reference 4 [14] – selects preset reference 4.
If the active preset reference is changed, it will merge with other preset reference commands com-
ing from either the digital inputs or via a fieldbus.
[15] Select preset ref 5
Select preset reference 5 [15] – selects preset reference 5.
If the active preset reference is changed, it will merge with other preset reference commands com-
ing from either the digital inputs or via a fieldbus.
[16] Select preset ref 6
Select preset reference 6 [16] – selects preset reference 6.
If the active preset reference is changed, it will merge with other preset reference commands com-
ing from either the digital inputs or via a fieldbus.
[17] Select preset ref 7
Select preset reference 7 [17] - selects preset reference 7.
If the active preset reference is changed, it will merge with other preset reference commands com-
ing from either the digital inputs or via a fieldbus.
[18] Select ramp 1
Select ramp 1 [18] - selects ramp 1.
[19] Select ramp 2
Select ramp 2 [19] - selects ramp 2.
[20] Select ramp 3
Select ramp 3 [20] - selects ramp 3.
[21] Select ramp 4
Select ramp 4 [21] - selects ramp 4.
[22] Run
Run [22] - issues a start command to the frequency converter.
[23] Run reverse
Run reverse [23] - issues a start reverse command to the frequency converter.
[24] Stop
Stop [24] - issues a stop command to the frequency converter.
[25] Qstop
Qstop [25] - issues a quick stop command to the frequency converter.
[26] Dcstop
Dcstop [26] - issues a DC stop command to the frequency converter.
[27] Coast
Coast [27] - the frequency converter coasts immediately. All stop commands including the coast
command stop the SLC.
[28] Freeze output
Freeze output [28] - freezes the output frequency of the frequency converter.
[29] Start timer 0
Start timer 0 [29] - starts timer 0, see par. 13-20 for further description.
[30] Start timer 1
Start timer 1 [30] - starts timer 1, see par. 13-20 for further description.
[31] Start timer 2
Start timer 2 [31] - starts timer 2, see par. 13-20 for further description.
[32] Set digital out A low
Set digital output A low [32] - any output with SL output A will be low.
[33] Set digital out B low
Set digital output B low [33] - any output with SL output B will be low.
[34] Set digital out C low
Set digital output C low [34] - any output with SL output Cwill be low.
3 Parameter descriptions FC 300 Programming Guide
192 MG.33.M8.02 - VLT
®
is a registered Danfoss trademark
3

Danfoss VLT AutomationDrive FC 300 Specifications

General

Brand	Danfoss
Model	VLT AutomationDrive FC 300
Category	DC Drives
Language	English