Danfoss vlt FC 102 User Manual

6.4.6 Data Readouts 16-**
Par.
No. #
Parameter description Default value 4-set-up FC 302
only
Change dur-
ing opera-
tion
Conver-
sion index
Type
16-0* General Status
16-00 Control Word 0 N/A All set-ups FALSE 0 V2
16-03 Status Word 0 N/A All set-ups FALSE 0 V2
16-3* AF Status
16-30 DC Link Voltage 0 V All set-ups FALSE 0 Uint16
16-34 Heatsink Temp. 0 °C All set-ups FALSE 100 Uint8
16-35 Inverter Thermal 0 % All set-ups FALSE 0 Uint8
16-36 Inv. Nom. Current ExpressionLimit All set-ups FALSE -2 Uint32
16-37 Inv. Max. Current ExpressionLimit All set-ups FALSE -2 Uint32
16-39 Control Card Temp. 0 °C All set-ups FALSE 100 Uint8
16-40 Logging Buffer Full [0] No All set-ups TRUE - Uint8
16-49 Current Fault Source 0 N/A All set-ups TRUE 0 Uint8
16-6* Inputs & Outputs
16-60 Digital Input 0 N/A All set-ups FALSE 0 Uint16
16-66 Digital Output [bin] 0 N/A All set-ups FALSE 0 Int16
16-71 Relay Output [bin] 0 N/A All set-ups FALSE 0 Int16
16-8* Fieldbus & FC Port
16-80 Fieldbus CTW 1 0 N/A All set-ups FALSE 0 V2
16-84 Comm. Option STW 0 N/A All set-ups FALSE 0 V2
16-85 FC Port CTW 1 0 N/A All set-ups FALSE 0 V2
16-9* Diagnosis Readouts
16-90 Alarm Word 0 N/A All set-ups FALSE 0 Uint32
16-91 Alarm Word 2 0 N/A All set-ups FALSE 0 Uint32
16-92 Warning Word 0 N/A All set-ups FALSE 0 Uint32
16-93 Warning Word 2 0 N/A All set-ups FALSE 0 Uint32
16-94 Ext. Status Word 0 N/A All set-ups FALSE 0 Uint32
6.4.7 AF Settings 300-**
NB!
Except for par. 300-10, it is not recommended to change the settings in this par. group for the Low Harmonic Drive
Par. No.
#
Parameter description Default value 4-set-up FC 302
only
Change
during op-
eration
Conver-
sion index
Type
300-0* General Settings
300-00 Harmonic Cancellation Mode [0] Overall All set-ups TRUE - Uint8
300-01 Compensation Priority [0] Harmonics All set-ups TRUE - Uint8
300-1* Network Settings
300-10 Active Filter Nominal Voltage ExpressionLimit 2 set-ups FALSE 0 Uint32
300-2* CT Settings
300-20 CT Primary Rating ExpressionLimit 2 set-ups FALSE 0 Uint32
300-21 CT Secondary Rating [1] 5A 2 set-ups FALSE - Uint8
300-22 CT Nominal Voltage 342 V 2 set-ups FALSE 0 Uint32
300-24 CT Sequence [0] L1, L2, L3 2 set-ups FALSE - Uint8
300-25 CT Polarity [0] Normal 2 set-ups FALSE - Uint8
300-26 CT Placement [1] Load Current 2 set-ups FALSE - Uint8
300-29 Start Auto CT Detection [0] Off All set-ups FALSE - Uint8
300-3* Compensation
300-30 Compensation Points 0.0 A All set-ups TRUE -1 Uint32
300-35 Cosphi Reference 0.500 N/A All set-ups TRUE -3 Uint16
VLT HVAC Low Harmonic Drive Operating In-
structions 6 How to Programme the Low Harmonic Drive
MG.16.A1.02 - VLT
®
is a registered Danfoss trademark 149
6

Danfoss vlt FC 102 Specifications

General

Brand	Danfoss
Model	vlt FC 102
Category	DC Drives
Language	English