Dell Inspiron 3502 User Manual

77 pages

To Next Page

To Previous Page

When disconnecting cables, keep them evenly aligned to avoid bending the connector pins. When connecting

cables, ensure that the ports and the connectors are correctly oriented and aligned.

CAUTION: Press and eject any installed card from the media-card reader.

CAUTION: Exercise caution when handling Lithium-ion batteries in laptops. Swollen batteries should not be used

and should be replaced and disposed properly.

NOTE: The color of your computer and certain components may appear differently than shown in this document.

Electrostatic discharge—ESD protection

ESD is a major concern when you handle electronic components, especially sensitive components such as expansion cards,

processors, memory DIMMs, and system boards. Very slight charges can damage circuits in ways that may not be obvious, such

as intermittent problems or a shortened product life span. As the industry pushes for lower power requirements and increased

density, ESD protection is an increasing concern.

Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than

in previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable.

Two recognized types of ESD damage are catastrophic and intermittent failures.

● Catastrophic – Catastrophic failures represent approximately 20 percent of ESD-related failures. The damage causes

an immediate and complete loss of device functionality. An example of catastrophic failure is a memory DIMM that has

received a static shock and immediately generates a "No POST/No Video" symptom with a beep code emitted for missing or

nonfunctional memory.

● Intermittent – Intermittent failures represent approximately 80 percent of ESD-related failures. The high rate of

intermittent failures means that most of the time when damage occurs, it is not immediately recognizable. The DIMM

receives a static shock, but the tracing is merely weakened and does not immediately produce outward symptoms related to

the damage. The weakened trace may take weeks or months to melt, and in the meantime may cause degradation of memory

integrity, intermittent memory errors, etc.

The more difficult type of damage to recognize and troubleshoot is the intermittent (also called latent or "walking wounded")

failure.

Perform the following steps to prevent ESD damage:

● Use a wired ESD wrist strap that is properly grounded. The use of wireless anti-static straps is no longer allowed; they do not

provide adequate protection. Touching the chassis before handling parts does not ensure adequate ESD protection on parts

with increased sensitivity to ESD damage.

● Handle all static-sensitive components in a static-safe area. If possible, use anti-static floor pads and workbench pads.

● When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static

packing material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you

discharge static electricity from your body.

● Before transporting a static-sensitive component, place it in an anti-static container or packaging.

ESD field service kit

The unmonitored Field Service kit is the most commonly used service kit. Each Field Service kit includes three main components:

anti-static mat, wrist strap, and bonding wire.

Components of an ESD field service kit

The components of an ESD field service kit are:

● Anti-Static Mat – The anti-static mat is dissipative and parts can be placed on it during service procedures. When using an

anti-static mat, your wrist strap should be snug and the bonding wire should be connected to the mat and to any bare metal

on the system being worked on. Once deployed properly, service parts can be removed from the ESD bag and placed directly

on the mat. ESD-sensitive items are safe in your hand, on the ESD mat, in the system, or inside a bag.

● Wrist Strap and Bonding Wire – The wrist strap and bonding wire can be either directly connected between your wrist

and bare metal on the hardware if the ESD mat is not required, or connected to the anti-static mat to protect hardware that

is temporarily placed on the mat. The physical connection of the wrist strap and bonding wire between your skin, the ESD

mat, and the hardware is known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never

Working inside your computer

Questions and Answers:

C
Christopher HaydenJul 28, 2025
How to replace a swollen battery in Dell Inspiron 3502 Laptop?
- A
  Ashley YoungJul 28, 2025
  Swollen batteries should not be used. Contact Dell product support for options to replace a swollen battery under the terms of the applicable warranty or service contract.
M
Mary SmithAug 13, 2025
What to do if the battery gets stuck in my Dell Inspiron 3502 Laptop?
- B
  Brent MorenoAug 13, 2025
  If the battery gets stuck in your Dell Laptop as a result of swelling, do not try to free it. Puncturing, bending, or crushing a battery can be dangerous.

Dell Inspiron 3502 Specifications

General

Graphics	Intel UHD Graphics 600
Operating System	Windows 10 Home
Battery	3-cell, 42 WHr
Processor	Intel Celeron N4020
RAM	4GB DDR4
Storage	256GB SSD
Weight	1.83 kg
Ports	1 x USB 2.0, 2 x USB 3.2 Gen 1, 1 x HDMI 1.4, 1 x SD card reader, 1 x headphone/microphone combo
Wireless	802.11ac
Dimensions	364 x 249 x 20 mm (14.33 x 9.80 x 0.79 inches)
Display	15.6-inch HD (1366 x 768) / 15.6-inch FHD (1920 x 1080)