Denon AVR-2311CI User Manual

8
ENGLISH
• In STEP 2, you will perform measurements at the
main listening position.
• This step automatically checks the speaker
configuration and speaker size, and calculates the
channel level, distance, and crossover frequency.
It also corrects distortion in the listening area.
6
6HOHFW ³0HDVXUH´ DQG WKHQ SUHVV
ENTER
When measuring begins, a test tone is
output from each speaker.
• Measurement requires several minutes.
7
7KHGHWHFWHGVSHDNHUVDUHGLVSOD\HG
>@
67(36SNU'HWHFW&KHFN
*RWR6WHS0HDVXUHPHQWDIWHUVSHDNHUFKHFN
5HWU\
1H[W0HDVXUHPHQW
)URQW
&HQWHU
6XEZRRIHU
6XUURXQG
<HV
<HV
<HV
<HV
$8726(783
$8'<66(<$8726(783
0XOW(4
(17(5 (QWHU 5(7851 &DQFHO
NOTE
If a connected speaker is not displayed, the
speaker may not be connected correctly. Check
the speaker connection.
8
8VH ui WR VHOHFW ³1H[W 1
0HDVXUHPHQW´DQGWKHQSUHVV
ENTER
• In STEP 3, you will perform measurements at
multiple positions (two to eight positions) other
than the main listening position.
• You can achieve a more effective correction of
distortion within the listening area by performing
measurements at multiple positions.
9
0RYHWKHVHWXSPLFURSKRQHWR
SRVLWLRQXVH
uiWRVHOHFW
³0HDVXUH´DQGWKHQSUHVV
ENTER
The measurement of the second position
starts. Measurements can be made in up to
six positions.
>@
67(30HDVXUHPHQW
3OHDVHSODFHWKHPLF
URSKRQHDWHDUKHLJKW
DWQGOLVWHQLQJ
SRVLWLRQ
6WDUWQH[WPHDVXUHPHQW7HVW7RQHZLOOVWDUW
$8726(783
$8'<66(<$8726(783
0XOW(4
(17(5 (QWHU 5(7851 &DQFHO
0HDVXUH
1H[W&DOFXODWLRQ
If you want to omit measurements from the next
position onward, select “Next 1 Calculation”.
(Go to
STEP4 Calculation
)
10
5HSHDWVWHSPHDVXULQJSRVLWLRQV
WR
When measurement of position 6 is
completed, a “Measurements finished.”
message is displayed.
>@
67(30HDVXUHPHQW
0HDVXUHPHQWVILQLVKHG
3URFHHGWR6WHS$QDO\]H
$8726(783
$8'<66(<$8726(783
0XOW(4
(17(5 (QWHU 5(7851 &DQFHO
5HWU\
1H[W&DOFXODWLRQ
Set up speakers (Audyssey
®
Auto Setup)
STEP 1
Preparation
4
&RQQHFWWKHVHWXSPLFURSKRQHWRWKH
6(7830,&MDFNRIWKLVXQLW
>@
67(33UHSDUDWLRQ
&RQQHFWWKHVSHDNHUV
DQGSODFHWKHPDFFRUG
LQJWRWKHUHFRPPHQGD
WLRQVLQWKHPDQXDO
6HWWKHIROORZLQJ
LWHPVLIQHFHVVDU\
6WDUW$XWR6HWXS
$PS$VVLJQ
&KDQQHO6HOHFW
$XWR6HWXS6WDUW
$8726(783
$8'<66(<$8726(783
0XOW(4
(17(5 (QWHU 5(7851 &DQFHO
When the setup microphone is
connected, the following screen is
displayed.
Here, we explain setup using the example of
5.1-channel speaker playback.
For settings other than 5.1-channel surround,
select “Amp Assign” and perform step 3 to 4 of
“Set up speakers” (vpage36).
If unused channels are set with “Channel Select”,
measuring time can be shortened. For setting,
perform steps 5 to 9 of “Set up speakers”
(vpage37).
5
8VHuiWRVHOHFW³$XWR6HWXS6WDUW´
DQGWKHQSUHVV
ENTER
NOTE
If “Caution” is displayed:
Go to “Error messages” (vpage 10), check
any related items, and perform the necessary
procedures.
If the problem is resolved, return and restart
“Audyssey Auto Setup”.
When performing Audyssey Auto
Setup over again
Press ui to select “Retry”, and then press ENTER .
When measuring has stopped
q Press RETURN, to the “Cancel Auto Setup?”
prompt is displayed.
w Press
o to select “Yes”, then press ENTER.
Setting up the speakers again
Repeat the operation from step 4 of
STEP 1 Preparation
.
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting Return to previous menu
STEP 2
Speaker Detection
STEP 3
Measurement

Denon AVR-2311CI Specifications

General

Brand	Denon
Model	AVR-2311CI
Category	Stereo Receiver
Language	English