92
＜
Linkage Menu
＞
+(/,&237(5
$,53/$1(
*/,'(5
ڀ ŪŲŃƗƒŃŷŤťůŨŃŲũŃŦŲűŷŨűŷŶ
ŏ5HWXUQWR/LQNDJH0HQX
ŏ7RXFKWKH>)DLO6DIH@EXWWRQLQWKH/LQNDJH0HQXWR
FDOOWKHVHWXSVFUHHQVKRZQEHORZ
)DLO6DIH
6HWVWKHVHUYRVRSHUDWLQJSRVLWLRQZKHQWUDQVPLWWHUVLJQDOV
FDQQRORQJHUEHUHFHLYHGRUZKHQWKHUHFHLYHUEDWWHU\
YROWDJHGURSV
7KHGLVSOD\VFUHHQLVDQH[DPSOH7KHVFUHHQGHSHQGVRQWKHPRGHOW\SH
The Failsafe function is used to set up positions that the
servos will move to in the case of radio interference.
Defines servo position when signals are lost and when
receiver battery voltage becomes low.
You may set either of two positions for each channel:
Hold, where the servo maintains its last commanded
position, or fail safe, where each servo moves to a
predetermined position. You may choose either mode for
each channel.
The T32MZ-WC system also provides you with an
advanced battery monitoring function that warns
you when the receiver battery has only a little power
remaining. In this case, each servo is moved to the
defined failsafe position. The battery failsafe may
be released by operating a predefined control on the
transmitter (default is throttle). 'RQRWFRQWLQXHWRÀ\
ODQGDVVRRQDVSRVVLEOH5HPHPEHULIWKHSUHGH¿QHG
)DLOVDIHVHWWLQJSURFHGXUH
Decide which channels you want to go to preset
positions, and which ones you want to maintain their
last commanded position. To select the fail safe mode
\RXZLVKWRVHWXVHWKH)6EXWWRQ7KLVEXWWRQWRJJOHV
EHWZHHQWKHWZRPRGHV+ROG)6
F/S mode setting:
7RXFKWKH)6EXWWRQRIWKHFKDQQHO\RXZDQWWR
VHWDQGVHWWKDWFKDQQHOWRWKH>)6@PRGH
+ROGWKHFRUUHVSRQGLQJVWLFNFRQWUROVOLGHURU
RWKHUFRQWUROLQWKHSRVLWLRQ\RXZDQWWKHVHUYRWR
PRYHWRZKHQWKHIDLOVDIHIXQFWLRQLVDFWLYDWHG
DQGWRXFKWKH)6SRVLWLRQEXWWRQ7KDWSRVLWLRQLV
GLVSOD\HGLQSHUFHQWDJH
:KHQ\RXZDQWWRUHWXUQWKDWFKDQQHOWRWKH+ROG
PRGHWRXFKWKH>)6@EXWWRQDJDLQ
%DWWHU\IDLOVDIHVHWWLQJSURFHGXUH
7RVHOHFWWKH%)6PRGHWRXFKWKH>%)6@EXWWRQ(DFK
time the button is touched, it toggles between [OFF] and
>%)6@
control suddenly moves to a position you did not
command, land at once and check your receiver battery.
'RQRWFRQWLQXHWRIO\ODQGDVVRRQDVSRVVLEOH
Defines servo position when signals are lost and when
receiver battery voltage becomes low.
:$51,1*
For safety, always set the fail safe functions.
■
Especially set the throttle channel fail safe function so that
WKHVHUYRPRYHVWRWKHPD[LPXPVORZVLGHIRUDLUSODQHVDQG
to the slow side from the hovering position for helicopters.
Crashing of the model at full high when normal radio
waves cannot be received due to interference, etc., is very
dangerous.
■
If fail safe is reset by throttle stick movement, the fail safe
may be mistaken as an engine malfunction and will be reset
DWORZWKURWWOHDQGWKHPRGHOZLOOFRQWLQXHWRÀ\,I\RXKDYH
any doubts, immediately land.
B.F/S setting:
7RXFKWKH>%)6@EXWWRQRIWKHGHVLUHGFKDQQHOWR
VHWLWWRWKH%)6PRGH
+ROGWKHFRUUHVSRQGLQJVWLFN95VOLGHURURWKHU
FRQWUROLQWKHSRVLWLRQ\RXZDQWWKHVHUYRWRPRYH
WRZKHQWKHEDWWHU\IDLOVDIHIXQFWLRQLVDFWLYDWHG
DQGWRXFKWKH)6SRVLWLRQEXWWRQ7KLVSRVLWLRQLV
GLVSOD\HGLQSHUFHQWDJH
:KHQ\RXZDQWWRUHWXUQWKDWFKDQQHOWR2))
WRXFKWKH>%)6@EXWWRQDJDLQ
%DWWHU\)DLOVDIH5HOHDVH)XQFWLRQ
This function releases the predefined control from it's
held position after indicating that your receiver battery is
low.
(QWHUWKHFRQWUROVHWWLQJVFUHHQE\WRXFKLQJWKH
%DWWHU\)65HOHDVHEXWWRQ1RZ\RXPD\FKRRVH
ZKHWKHUPRYLQJWKHWKURWWOHUHVHWVWKHFRQGLWLRQ
RUVHOHFWDVWLFNRUVZLWFKWRGHDFWLYDWHLW7RVHWD
GHVLUHGWKURWWOHUHOHDVHSRVLWLRQPRYHWKHWKURWWOH
VWLFNWRWKHSRLQWDWZKLFK\RXZLVKWKH%)6WREH
UHOHDVHG
ŏ7R6ZLWFK!
VFUHHQ
To Next Page
Loading...
Need help?
General
