LYNX Touch Installation and Setup Guide
- 40 -
Programming the Control
Program Reporting
When Compass service is required and GSM or IP are the only reporting channels: As part of Primary Central Station
programming; the “Phone Type” must be set to any selection other than “None”, the “Communicator Type” must be set to
GSM or IP, as applicable, and must match the compass value; “Phone number” field must be left blank and an “Account
number” must be programmed.
The following system options are programmed in this section:
Option Function
Primary or Secondary CS Info
Enroll information pertaining to the Primary and/or Secondary Central Station.
Phone Type Select the Report Format that will be used to send reports to the Primary or Secondary
Central Station, as applicable.
Phone Number Enter the Phone Number for the Primary or Secondary Central Station, as applicable.
Communicator Type Select the type of Communications Module that will be used to communicate with the Primary
or Secondary Central Station, as applicable.
Account Number Enter the account number for the Primary or Secondary Central Station, as applicable.
Dynamic Priority Select the primary method for sending Reports to the Primary or Secondary Central Station,
as applicable.
Dynamic Delay Selects delay between switching between reporting methods. Active if Dynamic Delay feature
has been set to Preferred Telco or Preferred Radio.
Report All Enable All Reports to be sent to the Primary or Secondary Central Station, as applicable.
Report Alarms Enable Alarm Reporting to the Primary or Secondary Central Station, as applicable.
Report Troubles Enable Trouble Reporting to the Primary or Secondary Central Station, as applicable.
Report Open/Close Enable Open/Close Reporting to the Primary or Secondary Central Station, as applicable.
Report Tests Enable Test Reporting to the Primary or Secondary Central Station, as applicable.
Follow Me Phone 1 or Phone 2
Enroll information Primary and/or Secondary telephone numbers for “Follow Me”
Announcements and/or Reminders. (This feature is only available on the LYNX Touch
L5200/L5200CN)
Phone Type Enter Number for Follow Me Phone 1 or Phone 2, as applicable.
Phone Number Enter Primary and/or Secondary telephone numbers for “Follow Me” Announcements and/or
Reminders.
Report All Enable All Reports to be sent to the Follow Me Phone 1 or Phone 2, as applicable.
Report Alarms Enable Alarm Reporting to the Follow Me Phone 1 or Phone 2, as applicable.
Report Troubles Enable Trouble Reporting to the Follow Me Phone 1 or Phone 2, as applicable.
Report Open/Close Enable Open/Close Reporting to the Follow Me Phone 1 or Phone 2, as applicable.
Report Tests Enable Test Reporting to the Follow Me Phone 1 or Phone 2, as applicable.
Report Selection
Enable Reporting of Specific Events
Options
PBX Enter the digits required to access telephone service. (Not applicable to the L7000/L7000CN)
Call Wait Cancel Enter the digits required to cancel call waiting, if applicable (Not applicable to the L7000/
L7000CN)
Number of Reports Limit the number of messages sent to the Central Station during an armed period.
Alarm Report Delay
Disable or select the time delay for alarm reporting (applies to L5200CN/L7000CN only)
Swinger Shutdown Select the number of times reports are sent and sounder sounds for non-fire alarms before
the system ignores subsequent alarms (applies to L5200/L7000 and only)
Abort Window Select the time delay for alarm reporting (applies to L5200/L7000 only)
First Offset Report Select the time for the first test report following power-up/programming or downloading
Report Frequency Select the test report frequency
Downloade
Phone Answer Enable to allow control to answer incoming phone line. (Not applicable to the L7000/
L7000CN)
Modem Speed (Future Use)
Ans. Machine Defeat Enable to defeat answering machine mode. (Active if Phone Answer feature is enabled.)
(Not applicable to the L7000/L7000CN)
Ring Counter Enter the number of rings before control picks up phone line. (Active if Ans. Machine Defeat is
not enabled.)
Callback Number Enter the phone number the control will use to call back the downloading computer. (Active if
Phone Answer is enabled.)
Flexible Callback Allows Download operator to temporarily change the callback number by the number of digits
selected. Active if Phone Answer is enabled
Number Enter the number of flexible callback numbers that will be used. Available if Flexible Callback
is enabled.
To Next Page
Loading...
Need help?
General
