EasyManuals Logo
Home>HP>Monitor>Z38c

HP Z38c User Manual

HP Z38c
30 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #24 background imageLoading...
Page #24 background image
3 Support and troubleshooting
Solving common problems
The following table lists possible problems, the possible cause of each problem, and the recommended
solutions.
Problem Possible Cause Solution
Screen is blank or video is
ashing.
Power cord is disconnected. Connect the power cord.
Power is o. Press the front panel power button.
NOTE: If pressing the power button has no eect, press and
hold the power button for 10 seconds to disable the power
button lockout feature.
Master power switch is turned o. Set the master power switch on the rear of the monitor to the
On position.
Video cable is improperly connected. Connect the video cable properly. Refer to Connecting the
cables on page 8 for more information.
System is in sleep mode. Press any key on the keyboard or move the mouse to
inactivate the screen blanking utility.
Video card is incompatible. Open the OSD menu and select the Input Control menu. Set
Auto-Switch Input to O and manually select the input.
Image appears blurred,
indistinct, or too dark.
Brightness setting is too low. Open the OSD menu and select Brightness to adjust the
brightness scale as needed.
Check Video Cable is
displayed on the screen.
Monitor video cable is disconnected. Connect the appropriate video signal cable between the
computer and monitor. Be sure that the computer power is o
while connecting the video cable.
Input Signal Out of Range is
displayed on the screen.
Video resolution and/or refresh rate
are set higher than what the monitor
supports.
Change the settings to a supported setting (see Preset display
resolutions on page 22).
The monitor is o but it did
not seem to enter a low-
power sleep mode.
The monitor's power saving control is
disabled.
Open the OSD menu and select Power Control, select Auto-
Sleep Mode, and then set auto-sleep to On.
OSD Lockout is displayed. The monitor's OSD lockout function is
enabled.
Press and hold the menu button on the front panel for 10
seconds to disable the OSD lockout function.
Power Button Lockout is
displayed.
The monitor's power button lockout
feature is enabled.
Press and hold the power button for 10 seconds to unlock the
power button function.
Button lockouts
Holding down the power button or menu button for ten seconds will lock out the functionality of the buttons.
You can restore the functionality by holding the buttons down again for ten seconds. This functionality is only
available when the monitor is powered on, displaying an active signal, and the OSD is not open.
18 Chapter 3 Support and troubleshooting

Other manuals for HP Z38c

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP Z38c and is the answer not in the manual?

HP Z38c Specifications

General IconGeneral
3DNo
HD typeUltraWide Quad HD+
Pixel pitch0.22908 x 0.22908 mm
Display diagonal37.5 \
Display resolution3840 x 1600 pixels
Display technologyLED
Native aspect ratio21:9
Viewable size, vertical366.5 mm
Contrast ratio (dynamic)5000000:1
Contrast ratio (typical)1000:1
Display number of colors1.073 billion colors
Viewable size, horizontal879.6 mm
Digital vertical frequency24 - 76 Hz
Digital horizontal frequency27 - 130 kHz
Display brightness (typical)300 cd/m²
Supported graphics resolutions640 x 480 (VGA), 720 x 400, 800 x 600 (SVGA), 1280 x 1024 (SXGA), 1280 x 720 (HD 720), 1280 x 768 (WXGA), 1440 x 900 (WXGA+), 1600 x 1200 (UXGA), 1600 x 900, 1920 x 1080 (HD 1080), 1920 x 1200 (WUXGA), 1920 x 1600, 2560 x 1080, 2560 x 1600 (WQXGA)
On/off switchYes
USB hub version3.2 Gen 1 (3.1 Gen 1)
USB upstream port typeUSB Type-C
VGA (D-Sub) ports quantity0
USB Type-A downstream ports quantity3
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Power consumption (max)195 W
Annual energy consumption93 kWh
Power consumption (standby)0.5 W
Power consumption (typical)80 W
Product colorBlack
Country of originChina
Market positioningBusiness
Tilt angle range-5 - 20 °
Number of OSD languages10
Panel mounting interface100 x 100 mm
On Screen Display (OSD) languagesCHI (SIMPL), CHI (TR), DEU, DUT, ENG, ESP, FRE, ITA, JPN, POR
Weight and Dimensions IconWeight and Dimensions
Depth (with stand)248 mm
Height (with stand)558.7 mm
Weight (with stand)13800 g
Depth (without stand)104.2 mm
Width (without stand)895.5 mm
Height (without stand)399.5 mm
Weight (without stand)9800 g

Related product manuals