Icom IC-F9511T User Manual

4-1-8 Basic Operation
(IC-F9510 series)
Turnin
g
power ON
AUTOMATIC SCAN TYPE:
g
When you use the transceiver for the first time, or
after the transceiver has not been used for a long
time, make sure to check the date and time
indication after turning the power ON. If the time and
date are not correct, reset
them.
cPush [ ] to turn the power ON.
Channel setting is not necessary for this type. When
turning power ON, the transceiver automatically
starts scanning. Scanning stops when receiving a call.
*Simple model only
Receiving and transmitting
Receiving:
dIf the transceiver is programmed for a start
up password, input the digit codes as
directed by your dealer.
• 10-keypad* can be used for password input.
*10-key model only:
• The keys as below can be used for
password input:
The transceiver detects numbers in the same block
cPush [ ] to turn the power ON.
2Push [CH Up] or [CH Down], or rotate [CH
Up/Down]* to select a channel, in sequence.
eWhile receiving a call, adjust the audio output level
to a comfortable listening level.
*Simple model only
Transmitting:
The transceiver detects numbers in the same block
as identical. Therefore “01234” and “56789” are
the same.
Transmitting:
Wait for the channel to become clear to avoid
interference.
c Take the microphone off hook.
• The ‘audible’ condition is selected and BUSY
indicator lights green.
• A priority channel may be selected automatically.
d Wait for the channel to become clear.
• The channel is busy when BUSY indicator lights
*In this instruction manual, these keys are
from the left, called [P0]/[P1]/[P2]/[P3]/[P4].
e
Wh th “PASSWORD” i di ti d t
• The channel is busy when BUSY indicator lights
green.
e While pushing and holding [PTT], speak into the
microphone at your normal voice level.
f Release [PTT] to receive.
 IMPORTANT: To maximize the readability of your
 signal;

e
Wh
en
th
e
“PASSWORD” i
n
di
ca
ti
on
d
oes
no
t
clear after entering 6 digits, the input code
number may be incorrect. Turn the power off
and start over in this case.
Channel selection
Several types of channel selections are available.
M th d diff di t t t

1. Pause briefly after pushing [PTT].
 2. Hold the microphone 5 to 10 cm (2 to 4 inches)
 from your mouth, then speak into the microphone
 at a normal voice level.
Transmitting notes
• Transmit inhibit function
T
he transceiver has several inhibit functions which
M
e
th
o
d
s
may
diff
er
accor
di
ng
t
o
your
sys
t
em
se
t
up.
NON-ZONE TYPE:
To select the desired operating channel:
• Push [CH Up] or [CH Down].
• Rotate [CH Up/Down]*.
• Push one of [MR-CH 1] to [MR-CH 4].
ZONE TYPE:
restrict transmission under the following conditions:
➣ The channel is in mute condition (‘Inaudible’
condition; “ ” does not appear.)
➣ The channel is busy.
➣ Un-matched (or matched) CTCSS is received.
(Depending on the pre-set value.)
➣ Un-matched (or matched) NAC is received.*
(Depending on the pre
-
set value )
38
ZONE TYPE:
To select the desired zone:
• Push [Zone], then push [CH Up] or [CH Down].
• Rotate [Zone Up/Down]*.
(Depending on the pre
set value
.
)
➣ The selected channel is a ‘receive only’ channel.
*Digital mode operation only.

Icom IC-F9511T Specifications

General

Brand	Icom
Model	IC-F9511T
Category	Transceiver
Language	English