Icom IC-F9511T User Manual

■ Tactical Grou
p
function
Clearing the tactical group in zone 128
4-1-11 Tactical Group Function
(IC-F9510 series)
p
The Tactical Group function enables commonly
used channels to be placed together in zone 128.
 IMPORTANT!
 The tactical group operation should be enabled
 by your dealer with the CS-F9010/F9510
 cloning software.
—
Individual channel clearing
1Push [CH Up] or [CH Down], or rotate
[CH Up/Down] to select the channel which you
wish to clear from zone 128, then turn power
O FF.
2 While pushing [P1] and [P3], push [ ] to turn
p
ower ON.
Creating the tactical group in zone 128
— Individual channel copy
1Push [CH Up] or [CH Down], or rotate
[CH Up/Down] to select the channel which you
wish to copy to zone 128, then turn power OFF.
2 While pushing [P1] and [P3], push [ ] to turn
power ON.
“
COPY ?”
i di l d
p
• “CLEAR ?” is displayed.
• Turn power OFF to cancel clearing.
3Push [P0] to clear the selected channel from
zone 128.
• “CLEARED” is displayed.
Clearing the tactical group in zone 128
—
Zone clearing
•
“
COPY ?”
i
s
di
sp
l
aye
d
.
• When all 512 channels are already used, the
transceiver has no capacity. “NOT COPY” is
displayed for 2 sec and error beeps sound.
• Turn power OFF to cancel copy.
3Push [P0] to copy the selected channel to zone
128.
• “COPIED” is displayed.
Zone clearing
1Push [CH Up] or [CH Down], or rotate
[CH Up/Down] to select a channel in zone 128,
then turn power OFF.
2While pushing [P1] and [P3], push [ ] to turn
power ON.
• “CLEAR ?” is displayed.
• Turn
p
ower OFF to cancel clearin
g
.
Creating the tactical group in zone 128
—Zone copy
1Push [CH Up] or [CH Down], or rotate
[CH Up/Down] to select the channel belonging
to the zone which you wish to copy to zone 128,
then turn power OFF.
2 While
p
ushin
g
[
P1
]
and
[
P3
]
,
p
ush
[
]
to turn
pg
3Push [CH Up] or [CH Down], or rotate
[CH Up/Down] to select “ALL CLEAR ?”.
4Push [P0] to clear the zone data from zone 128.
• “ALL CLEARED” is displayed.
Cloning the tactical group
<Master (Zone 128) ➔ Sub (Zone 128)>
Thi i bl h i
pg
[]
[]
,p [ ]
power ON.
• “COPY ?” is displayed.
• When all 512 channels are already used, the
transceiver has no capacity. “NOT COPY” is
displayed for 2 sec and error beeps are
emitted.
• Turn power OFF to cancel copy.
Thi
s
operat
i
on
ena
bl
es
t
h
e
master
transce
i
ver
to
clone it’s own tactical group in zone 128 to zone
128 of the sub transceiver.
 IMPORTANT!
 To perform the tactical group cloning, “Set
 mode access” must be enabled, and the dealer
 pass code must be inputted.
3Push [CH Up] or [CH Down], or rotate
[CH Up/Down] to select “ZONE COPY ?”.
4Push [P0] to copy the selected zone data to
zone 128.
• “COPIED” is displayed.
 NOTE:

When the transceiver has not enou
g
h capacit
y
to
1Connect the two transceivers (master and sub)
with the optional zone copy cable. The
following zone copy cables are available;
• OPC-1532 : Used for the Mobile to Mobile
connection.
• OPC-1871 : Used for the Handheld to
Mobile connection.
57
 gy
 create the tactical group with zone copy, all
 channel data may not be copied completely.

Icom IC-F9511T Specifications

General

Brand	Icom
Model	IC-F9511T
Category	Transceiver
Language	English