5 - 11
5-3 TRANSMIT ADJUSTMENT (Continued)
5-4 RECEIVE ADJUSTMENTS
1) Select an adjustment item (band) using
/
.
2) Set the SSG as specifi ed (frequency, deviation and output level), and then push
to automatically adjust.
ADJUSTMENT
ADJUSTMENT
ITEM
OPERATION VALUE
RECEIVE
SENSITIVITY
[A-BAND]
NOTE:
“RECEIVE SENSITIVITY” must be adjusted before “S-METER.” Otherwise, “S-METER” will
not be adjusted properly.
– 1 1) Set the power supply voltage to 7.4 V.
2) Connect an SSG to the antenna connector, and then set it as;
Frequency : (Displayed on the function display)
Level : –10 dBµ (–117 dBm)
†
Modulation : 1 kHz
Deviation : 3.5 kHz
–
(137.02 MHz)
[VTL] 2
Push
.
(Automatic
adjustment)
(145.02 MHz)
[VTM] 3
(173.98 MHz)
[VTH] 4
(380.02 MHz)
[UTL] 5
(435.02 MHz)
[UTM] 6
(478.98 MHz)
[UTH] 7
[AIR BAND]
– 1 1) Set the power supply voltage to 7.4 V.
2) Connect an SSG to the antenna connector, and then set it as;
Frequency : (Displayed on the function display)
Level : –10 dBµ (–117 dBm)
†
Modulation : 1 kHz
Deviation : 30% (AM)
–
(108.02 MHz)
[ATL] 2
Push
.
(Automatic
adjustment)
(127.02 MHz)
[ATM] 3
(136.95 MHz)
[ATH] 4
[B-BAND]
– 1 1) Set the power supply voltage to 7.4 V.
2) Connect an SSG to the antenna connector, and then set it as;
Frequency : (Displayed on the function display)
Level : –10 dBµ (–117 dBm)
†
Modulation : 1 kHz
Deviation : 3.5 kHz
–
(137.02 MHz)
[VTL]
Push
.
(Automatic
adjustment)
(145.02 MHz)
[VTM] 2
(173.98 MHz)
[VTH] 3
(380.02 MHz)
[UTL] 4
(435.02 MHz)
[UTM] 5
(478.98 MHz)
[UTH] 6
S-METER
[BC BAND]
NOTE:
“RECEIVE SENSITIVITY” must be adjusted before “S-METER” and “S-METER S3 LEVEL.” Other-
wise, “S-METER” and “S-METER S3 LEVEL will not be adjusted properly.
–
1 1) Set the power supply voltage to 7.4 V.
2) Connect an SSG to the antenna connector and set it as;
Modulation : 1 kHz
Deviation : 30% (AM)
–
(AM S0 level)
[BS0]
2 • Set the SSG as;
Frequency : (Displayed on the function display)
Level : +2 dBµ (–105 dBm)
†
Push .
(Automatic
adjustment)
(AM S3 level)
[BS3]
3 • Set the SSG as;
Level : +5 dBµ (–102 dBm)
†
(AM Full scale)
[BSF]
4 • Set the SSG as;
Frequency : (Displayed on the function display)
Level : +12 dBµ (–95 dBm)
†
(WFM S0 level)
[BS0]
5 • Set the SSG as;
Frequency : (Displayed on the function display)
Level : +2 dBµ (–105 dBm)
†
(WFM S3 level)
[BS3]
6 • Set the SSG as;
Frequency : (Displayed on the function display)
Level : +5 dBµ (–102 dBm)
†
(WFM Full scale)
[BSF]
7 • Set the SSG as;
Frequency : (Displayed on the function display)
Level : +12 dBµ (–95 dBm)
†
†
; This output level of a standard signal generator (SSG) is indicated as SSG’s open circuit.
To Next Page
Loading...
Need help?
General
