8ENGLISH
Water Hardness Table
Level °dH German
degrees
°fH French
degrees
°Clark English
degrees
1 Soft 0 - 6 0 - 10 0 - 7
2 Medium 7 - 11 11 - 20 8 - 14
3 Average 12 - 16 21 - 29 15 - 20
4 Hard 17 - 34 30 - 60 21 - 42
5 Very hard 35 - 50 61 - 90 43 - 62
Water Softening System
Water softener automatically reduces water hardness, conse-
quently preventing scale buildup on heater, contributing also
to better cleaning eciency. This system regenerates itself with
salt, therefore it is required to rell salt container when empty.
Frequency of regeneration depends on water hardness level
setting - regeneration takes place once per 6 Eco cycles with
water hardness level set to 3.
Regeneration process starts in nal rinse and nishes in drying
phase, before cycle ends.
• Single regeneration consumes: ~3.5 L of water;
• Takes up to 5 additional minutes for the cycle;
• Consumes below 0.005 kWh of energy.
Filling the rinse aid dispenser
Rinse aid makes dish DRYING easier. The rinse aid dispenser
A
should be lled when the RINSE AID REFILL indicator light in
the control panel is lit.
1. Open the dispenser
B
by pressing and pulling up the tab on
the lid.
2. Carefully introduce the rinse aid as far as the maximum (110
ml) reference notch of the lling space - avoid spilling it. If this
happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the tub.
Adjusting the dosage of rinse aid
If you are not completely satised with the drying results, you
can adjust the quantity of rinse aid used.
• Switch the dishwasher on using the ON/OFF button.
• Switch it o using the ON/OFF button.
• Press button three times - a beep will be heard.
• Switch it on using the ON/OFF button.
• The current selection level number and rinse aid indicator
light ash.
• Press button to select the level of rinse aid quantity to be
supplied.
• Switch it o using the ON/OFF button.
Setting is complete!
B A
First Use
Advice regarding the rst time use
Before installation and rst usage of the appliance please read
carefully „ SAFETY INSTRUCTION” and „ASSEMBLY INSTRUCTION”
available in the product literature bag. Please remember to
remove all transport protection parts from the dishwasher.
Filling the salt reservoir
The use of salt prevents the formation of LIMESCALE on the
dishes andon the machine’s functional components.
• It is mandatory that THE SALT RESERVOIR BE NEVER EMPTY.
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher
(see PRODUCT DESCRIPTION) and should be lled when the
SALT REFILL indicator light in the control panel is lit.
1. Remove the lower rack and unscrew
the reservoir cap (anticlockwise).
2. Position the funnel (see gure) and
ll the salt reservoir right up to its
edge (approximately 1 kg); it is not
unusual for a little water to leak out.
3. Only the rst time you do this: ll
the salt reservoir with water.
4. Remove the funnel and wipe any
salt residue away from the opening.
Make sure the cap is screwed on tightly, so that no detergent
can get into the container during the wash program (this could
damage the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-Wash” program alone is NOT sucient.
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
Only use salt that has been specically designed for
dishwashers. If the salt container is not lled, the water
softener and the heating element may be damaged
as a result of limescale accumulation. Using of Salt is
recommended with any type of dishwasher detergent.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle to
avoid corrosion.
Setting the water hardness
To allow the water softener to work in a perfect way, it is
essential that the water hardness setting is based on the actual
water hardness in your house. This information can be obtained
from your local water supplier. The factory sets the default value
for the water hardness.
• Switch on the appliance by pressing the ON/OFF button.
• Switch o the appliance by pressing the ON/OFF button.
• Hold down button for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing quickly the ON/OFF
button.
• The current selection level number and the salt indicator light
both ash.
• Press button to select the desired hardness level (see
WATER HARDNESS TABLE).
• Switch o the appliance by pressing the ON/OFF button.
Setting is complete!
To Next Page
Loading...
Need help?
General
