IKONIX apt 400XAC Series User Manual

ii
4.3.13 Editing OC Fold ............................................................................. 50
4.3.14 Editing Lock ................................................................................... 50
4.3.15 Editing Mem Lock .......................................................................... 51
4.3.16 Editing Volt Sense ......................................................................... 52
4.3.17 Editing Ext Trig .............................................................................. 52
4.3.18 Editing Function ............................................................................. 53
SmartConfig .................................................................................. 53
4.4 Using Memories and Steps (PROGRAM Mode only) ........................... 55
4.4.1 Selecting a Memory ....................................................................... 55
4.4.2 Naming a Memory ......................................................................... 57
4.4.3 Selecting a Step ............................................................................ 58
4.5 Test Parameters Description ................................................................. 58
4.6 Editing Test Parameters ........................................................................ 62
4.6.1 Editing Start and End Angle (PROGRAM Mode only) ................... 64
4.6.2 Editing the Memory Cycle (PROGRAM Mode only) ...................... 65
4.6.3 Editing the Memory (PROGRAM Mode only) ................................ 66
4.6.4 Editing the Step (PROGRAM Mode only) ...................................... 66
4.6.5 Editing Voltage .............................................................................. 67
4.6.6 Editing Frequency.......................................................................... 68
4.6.7 Editing Transient * (PROGRAM Mode only) .................................. 68
4.6.8 Editing Trans-Volt* (PROGRAM Mode only) .................................. 69
4.6.9 Editing Trans-Site* (PROGRAM Mode only) ................................. 70
4.6.10 Editing Trans-Time* (PROGRAM Mode only) ................................ 71
4.6.11 Editing Trans-Cycle* (PROGRAM Mode only) ............................... 71
4.6.12 Editing Ramp Up (PROGRAM Mode only) .................................... 73
4.6.13 Editing Timer Unit (PROGRAM Mode only) ................................... 74
4.6.14 Editing Delay (PROGRAM Mode only) .......................................... 74
4.6.15 Editing Dwell (PROGRAM Mode only) .......................................... 75
4.6.16 Editing Ramp Down (PROGRAM Mode only) ............................... 76
4.6.17 Editing Step Cycle (PROGRAM Mode only) .................................. 76
4.6.18 Editing A Hi-Lmt & A Lo-Lmt (PROGRAM Mode only) ................... 77
4.6.19 Editing P Hi-Lmt & P Lo-Lmt (PROGRAM Mode only) .................. 78
4.6.20 Editing Ap Hi-Lmt & Ap Lo-Lmt (PROGRAM Mode only) ............... 79
4.6.21 Editing CF Hi-Lmt & CF Lo-Lmt (PROGRAM Mode only) .............. 80
4.6.22 Editing PF Hi-Lmt & PF Lo-Lmt (PROGRAM Mode only) .............. 81
4.6.23 Editing VA Hi-Lmt & VA Lo-Lmt (PROGRAM Mode only) .............. 82
4.6.24 Editing Q Hi-Lmt & Q Lo-Lmt (PROGRAM Mode only) .................. 83
4.6.25 Editing Prompt ............................................................................... 84
4.6.26 Editing Connect ............................................................................. 85
4.6.27 Editing Phase Set .......................................................................... 86
4.7 Reviewing Test Results ......................................................................... 86
5. Test Modes .................................................................................................. 88
5.1 Description of Test Modes .................................................................... 88
5.2 Initializing a Test in PROGRAM Mode .................................................. 88
5.2.1 AC Output ...................................................................................... 88
5.2.2 DC Output ..................................................................................... 90

IKONIX apt 400XAC Series Specifications

General

Brand	IKONIX
Model	apt 400XAC Series
Category	AC Power Distribution
Language	English