JVC ca-mx55mbk User Manual

| CA-MX55MBK
UT
iavem
catew-
Vaal
ealeis
_
| |
Using the Power Switch
4.
Press
the
POWER
switch
to
turn
on
the
stereo
system.
When
the
POWER
switch
is
not
pressed
and
the
power
cord
is
plugged
in,
the
stereo
is
in
STANDBY
mode
and
STANDBY
indicator
lights.
In
STANDBY
mode,
the
stereo
uses
a
small
amount
of
power
(10
watts)
forthe
clock,
memory
contents,
and
any
timers
which
are
set.
2.
To
disconnect
power
compietely,
unplug
the
power
cord.
Adjusting the Volume controls
Volume
Turn
the
VOLUME
knob
to
adjust
the
volume
level
of
the
speakers
or
headphones.
*
Connect
headphones
to
the
PHONES
jack
on
the
amplifier
for
listening
through
headphones.
No
sound
will
be
produced
from
the
speakers.
important!
There
is
danger
of
your
hearing
being
affected
if
you
listen
to
your
sound
system
at
an
excessively
high
volume
level.
You
must
be
especially
aware
of
this
danger
when
using
headphones.
Balance
Turn
the
BALANCE.
knob
to
adjust
the
left-and-right
sound
balance
in
the
speakers or headphones.
Bass Control
Turn
the
BASS
CONTROL
knob
to
adjust
the
output
level
of
the
low
frequencies.
Turning
this
contro!
toward
BOOST
will
boost
the
low
frequencies.
Using the SEA Graphic Equalizer
By
adjusting
the
frequency
levels
in
the
five
available
frequency
ranges
you
can
create
your
own
sound.
=10
@3Hz 280Hz tkHz dkHz 16xHz
Recording
with
the
SEA
Graphic
Equalizer
The
SEA
setting
for
a
source
such
as
CD
will
be
reproduced
when
the
source
material
is
recorded.
This
SEA
effect
can
be
eliminated
by
setting
all
the
SEA
control
slides
at
zero.
When
the
slide
lever
controls
on
the
SEA
Graphic
Equalizer
are
moved
in
the
direction
of
the
plus
the
sound
range
will
increase.
The
range
will
decrease
when
the
levers
are
moved
in
the
direction
of
the
minus.
Selecting the Source
Select
the
SOURCE
you
want
to
listen
to
with
SOURCE
SELECTOR
button.
SOURCE SELECTOR
*
Each
time
you
press
the
SOURCE
SELECTOR
buiton,
the
source
changes
to
the
next
one
in
the
sequence,
and
the
corresponding
SOURCE
indicator
lights.
<>
TAPE
«+
TUNER
+
CD
+
VIDEO/AUX
+»
PHONO
<>
Using Turntable, VCR and DAT
In addition to the CD Automatic Changer, Tuner, and Cassette Tape Deck,
the amplifier can also play a turntable, a VCR and a DAT.
1. Turn the power for each piece of component ON.
2. To play a record, press the SOURCE SELECTOR button on the
amplifier so that PHONO lights on the SOURCE Indicator.
To use VCR or DAT, press the SOURCE SELECTOR button on the
amplifier so that VIDEO/AUX lights on the SOURCE indicator.
3. To operate the each component, refer to Its instruction manual.
* You can operate a JVC VCR using the remote controller.
When VCR is connected, the sound is heard through the speakers.
Signal Level Indicator
The Signal Level Indicator shows the signal level of each frequency band
separately.
Remote Sensor
Receives the signal from the supplied Remote Control unit.
REMOTE SENSOR
9
(No. 20342) 11

JVC ca-mx55mbk Specifications

General

Brand	JVC
Model	ca-mx55mbk
Category	CD Player
Language	English